how to replace the brake pads on a Toyota Corolla E170 (2013-2019)

Toyota Corolla E170 (2013-2019)

Error Codes

1-2 hours

Time

medium

Difficulty

high

Severity

3 min read

555 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Step-by-step guide to replace brake pads on a 2013-2019 Toyota Corolla E170. Learn symptoms, diagnostic steps, tools, and safety tips.

Affected Component

Brakes

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery when working on electrical components.
•Ensure the vehicle is securely supported on jack stands before working underneath.

Symptoms

•Squeaking or squealing noise when brakes are applied
•Vibration or pulsation felt through the brake pedal
•Warning light illuminated on the dashboard
•Reduced braking efficiency
•Grinding noise indicating metal contact

Diagnostic Steps

1
Inspect brake pads for thickness; measure with a caliper.
2
Check brake rotor surface for grooves or scoring.
3
Examine brake fluid level in the master cylinder.
4
Inspect caliper and mounting hardware for damage or corrosion.
5
Test brake performance on a short drive.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack
•Jack stands
•Lug wrench
•Socket set
•C-clamp
•Brake cleaner
•Torque wrench

Parts Required

•New brake pads
•Brake grease (for caliper hardware)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Solution

1. Preparation

Tools Required: Jack, jack stands, lug wrench, socket set, C-clamp, brake cleaner, and torque wrench.
Park the vehicle on a flat surface and engage the parking brake.
Wear safety glasses and gloves for protection.

2. Lift the Vehicle

Loosen the lug nuts slightly on the front wheels while the vehicle is still on the ground.
Use the jack to lift the front of the vehicle and secure with jack stands.
Remove the lug nuts and take off the front wheels.

3. Remove the Brake Caliper

Locate the caliper mounting bolts on the back of the caliper.
Use the socket set to remove the caliper bolts.
Carefully slide the caliper off the rotor. Support it using a bungee cord or similar to prevent straining the brake line.

4. Replace the Brake Pads

Remove the old brake pads from the caliper bracket. Note their orientation for installation of new pads.
Use the C-clamp to compress the caliper piston back into the caliper housing. This allows enough space for the new, thicker brake pads.
Clean the caliper bracket and apply brake cleaner to remove dust and debris.
Install the new brake pads in the same orientation as the old ones.

5. Reinstall the Caliper

Slide the caliper over the new brake pads and rotor.
Reinsert and tighten the caliper mounting bolts to the manufacturer's specified torque (typically around 20-25 ft-lbs).
Reattach the wheel and hand-tighten the lug nuts.

6. Lower the Vehicle

Carefully lower the vehicle off the jack stands using the jack.
Tighten the lug nuts to the manufacturer's specified torque (usually 76-84 ft-lbs) in a crisscross pattern for even tightening.