how to replace brake pads on my Toyota Corolla E170 (2013-2019)

Toyota Corolla E170 (2013-2019)

Error Codes

1-2 hours

Time

medium

Difficulty

high

Severity

3 min read

600 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to replace brake pads on your 2013-2019 Toyota Corolla E170. Step-by-step guide with diagnostic steps, tools required, and safety tips.

Affected Component

Brakes

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always use jack stands when working under a vehicle.
•Allow the brake system to cool before handling components.

Symptoms

•Squeaking or squealing noises when braking
•Grinding sound indicating metal-to-metal contact
•Reduced braking efficiency
•Warning light on the dashboard related to brake system
•Vibration or pulsation in the brake pedal

Diagnostic Steps

1
Inspect brake pads visually through the wheel spokes to check for wear.
2
Check brake fluid level in the master cylinder reservoir.
3
Test brake function by pressing the pedal and observing response.
4
Scan for any error codes related to the braking system using OBD-II scanner.
5
Verify if brake rotors exhibit signs of wear or warping.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack
•Jack stands
•Lug wrench
•Socket set
•C-clamp or brake caliper tool
•Brake cleaner
•Torque wrench

Parts Required

•Brake pads
•Brake rotor

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect brake pads visually through the wheel spokes to check for wear.
2
Check brake fluid level in the master cylinder reservoir.
3
Test brake function by pressing the pedal and observing response.
4
Scan for any error codes related to the braking system using OBD-II scanner.
5
Verify if brake rotors exhibit signs of wear or warping.

Solution

1. Preparation

Tools Required: Jack, jack stands, lug wrench, socket set, C-clamp or brake caliper tool, brake cleaner, and a torque wrench.
Ensure the vehicle is parked on a flat surface and the engine is off.
Disconnect the negative battery cable for safety.

2. Remove Wheel

Use the lug wrench to loosen the lug nuts slightly while the vehicle is still on the ground.
Raise the vehicle with a jack.
Securely place jack stands under the vehicle.
Fully remove the lug nuts and take off the wheel.

3. Remove Brake Caliper

Locate the caliper mounting bolts (usually on the back side of the caliper).
Use the socket set to remove the caliper bolts.
Carefully slide the caliper off the brake rotor, supporting it with a bungee cord or hang it to avoid straining the brake line.

4. Replace Brake Pads

Remove the old brake pads from the caliper bracket.
Use the C-clamp or brake caliper tool to compress the caliper piston back into its housing.
Install the new brake pads in the same position as the old ones, ensuring that any anti-squeal shims are also placed.

5. Reinstall Brake Caliper

Position the caliper back over the new brake pads and rotor.
Reinsert and tighten the caliper mounting bolts to the manufacturer's torque specification (usually around 20-25 ft-lbs).
Double-check that the caliper is securely mounted.

6. Reassemble Wheel

Place the wheel back onto the hub.
Hand-tighten the lug nuts onto the wheel bolts.
Lower the vehicle off the jack stands.
Use the torque wrench to tighten the lug nuts to the manufacturer's specification (usually about 76 ft-lbs).

7. Final Checks

Reconnect the negative battery cable.
Pump the brake pedal a few times to seat the brake pads against the rotors.
Check brake fluid level and top off if necessary.