how to fix transmission slipping problems on Toyota Corolla E170 (2013-2019)

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

4 min read

667 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix transmission slipping issues in Toyota Corolla E170 (2013-2019). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Ensure the engine is off and the transmission is cool before removing the dipstick or working with fluid.
•Be cautious of sharp edges on the pan and ensure the vehicle is securely supported.
•Disconnect the battery before working on electrical components.

Symptoms

•Transmission slips during acceleration
•Delayed or harsh shifting between gears
•Engine RPMs increase without corresponding vehicle speed
•Warning lights illuminated on the dashboard (e.g., Check Engine light)
•Fluid leaks under the vehicle
•Unusual noises (e.g., whining or grinding) when the transmission is engaged

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any transmission-related issues.
2
Check the transmission fluid level and condition; look for burning smell or discoloration.
3
Inspect the transmission fluid for leaks under the vehicle and around transmission seals.
4
Examine the transmission filter for clogs or contamination.
5
Test the vehicle's throttle position sensor (TPS) for proper operation and response.
6
Check wiring and connectors related to the transmission for damage or corrosion.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Funnel
•Catch pan
•Multimeter
•Wire stripper/crimper
•Electrical cleaner

Parts Required

•Toyota ATF (Automatic Transmission Fluid)
•New transmission filter
•New gasket

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Symptoms

•Transmission slips during acceleration

•Delayed or harsh shifting between gears

•Engine RPMs increase without corresponding vehicle speed

•Warning lights illuminated on the dashboard (e.g., Check Engine light)

•Fluid leaks under the vehicle

•Unusual noises (e.g., whining or grinding) when the transmission is engaged

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any transmission-related issues.
2
Check the transmission fluid level and condition; look for burning smell or discoloration.
3
Inspect the transmission fluid for leaks under the vehicle and around transmission seals.
4
Examine the transmission filter for clogs or contamination.
5
Test the vehicle's throttle position sensor (TPS) for proper operation and response.
6
Check wiring and connectors related to the transmission for damage or corrosion.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is on a flat surface and the parking brake is engaged.
Disconnect the battery to avoid electrical shorts.

2. Check and Replace Transmission Fluid

Sub-steps:
- Locate the transmission dipstick and remove it.
- Wipe the dipstick clean and reinsert it to check the fluid level.
- If low, add the appropriate type of Toyota ATF (Automatic Transmission Fluid) as specified in the owner's manual.
- If fluid is burnt or dirty, proceed to replace the fluid.
Tools Required: Funnel, catch pan, socket set.
Safety Warnings: Ensure the engine is off and the transmission is cool before removing the dipstick or working with fluid.

3. Replace Transmission Filter

Sub-steps:
- Remove the transmission pan by loosening the bolts with a socket wrench.
- Carefully lower the pan and drain the old fluid into the catch pan.
- Remove the old transmission filter and replace it with a new filter, ensuring it seats properly.
- Clean the transmission pan and install a new gasket before reattaching the pan.
Tools Required: Socket set, gasket scraper, new filter, new gasket.
Safety Warnings: Be cautious of sharp edges on the pan and ensure the vehicle is securely supported.

4. Inspect and Repair Wiring and Connectors

Sub-steps:
- Visually inspect wiring harnesses and connectors leading to the transmission for damage or corrosion.
- Repair or replace damaged wiring as needed.
- Ensure connectors are clean and securely fastened.
Tools Required: Multimeter, wire stripper/crimper, electrical cleaner.
Safety Warnings: Disconnect the battery before working on electrical components.

5. Test Drive and Adjust

Sub-steps:
- Reconnect the battery and start the engine.
- Shift through the gears while the vehicle is stationary to check for smooth operation.
- Conduct a test drive to monitor for any slipping or unusual behavior.
Tools Required: None specific, but a safe driving environment is necessary.
Safety Warnings: Ensure the area is clear of obstacles and pedestrians before test driving.