how to fix the temperature gauge not working on my Toyota Corolla E170 (2013-2019)?

Toyota Corolla E170 (2013-2019)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

3 min read

532 words

Problem Statement

Learn how to diagnose and fix the temperature gauge issue in your 2013-2019 Toyota Corolla E170. Step-by-step guide with symptoms and solutions.

Affected Component

Cooling System

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before opening any cooling system components.

Symptoms

•Temperature gauge remains at zero or does not move
•Warning lights illuminated on the dashboard (e.g., check engine light)
•Engine overheating or running too cold (if noticeable)
•Inconsistent gauge readings when the engine is started
•Possible coolant leak or smell of coolant

Diagnostic Steps

1
Inspect the fuse related to the temperature gauge for any damage or failure.
2
Use an OBD-II scanner to check for any error codes related to the engine temperature or sensor.
3
Verify the operation of the coolant temperature sensor by checking its resistance with a multimeter.
4
Check the wiring and connections leading to the temperature gauge and sensor for any signs of damage or corrosion.
5
Inspect the engine coolant level and condition to ensure there are no leaks or low levels affecting gauge performance.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Multimeter
•Torque wrench
•Screwdriver set

Parts Required

•Coolant temperature sensor
•Electrical connector (if needed)
•Thread sealant (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the fuse related to the temperature gauge for any damage or failure.
2
Use an OBD-II scanner to check for any error codes related to the engine temperature or sensor.
3
Verify the operation of the coolant temperature sensor by checking its resistance with a multimeter.
4
Check the wiring and connections leading to the temperature gauge and sensor for any signs of damage or corrosion.
5
Inspect the engine coolant level and condition to ensure there are no leaks or low levels affecting gauge performance.

Solution

1. Preparation

Gather the necessary tools and parts.
Disconnect the battery to ensure safety while working on electrical components.

2. Replace the Coolant Temperature Sensor

Locate the Sensor:
- The coolant temperature sensor is typically found near the thermostat housing or on the engine block.
Remove the Old Sensor:
- Disconnect the electrical connector from the sensor.
- Use a socket wrench to carefully unscrew and remove the sensor from its location.
Install the New Sensor:
- Apply a small amount of thread sealant to the new sensor's threads (ensure it is compatible with coolant systems).
- Screw the new sensor into place and tighten it to the manufacturer's specified torque (usually around 15-20 ft-lbs).

3. Check Wiring and Connections

Inspect Wiring:
- Examine the wiring harness for any frayed wires or loose connections.
- Repair or replace any damaged wiring as necessary.
Reconnect Components:
- Reattach the electrical connector to the new sensor.
- Ensure all connections are secure.

4. Test the System

Reconnect the Battery:
- Ensure the battery is connected properly after the installation is complete.
Start the Engine:
- Allow the engine to reach operating temperature and observe the temperature gauge for proper function.
Verify Operation:
- Monitor for any warning lights and check if the temperature gauge moves within the normal range.