how to fix the ignition coil issue in my Toyota Corolla E170 (2013-2019)

Toyota Corolla E170 (2013-2019)

Error Codes

1-2 hours

Time

medium

Difficulty

high

Severity

3 min read

521 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix ignition coil issues in Toyota Corolla E170 (2013-2019). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Engine

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Allow engine to cool before opening any components.

Symptoms

•Check engine light illuminated
•Rough idle or engine stalling
•Loss of power during acceleration
•Decreased fuel efficiency
•Increased emissions
•Difficulty starting the engine

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify specific cylinder misfires or ignition coil errors.
2
Inspect the ignition coil visually for cracks, corrosion, or damage.
3
Test the primary and secondary resistance of the ignition coil with a multimeter.
4
Check the ignition coil connector for loose connections or corrosion.
5
Inspect spark plugs for wear or damage, as this can also affect ignition performance.
6
Perform a cylinder compression test to rule out internal engine issues.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Socket set
•Torque wrench
•Dielectric grease

Parts Required

•Replacement ignition coil(s)
•Spark plugs (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify specific cylinder misfires or ignition coil errors.
2
Inspect the ignition coil visually for cracks, corrosion, or damage.
3
Test the primary and secondary resistance of the ignition coil with a multimeter.
4
Check the ignition coil connector for loose connections or corrosion.
5
Inspect spark plugs for wear or damage, as this can also affect ignition performance.
6
Perform a cylinder compression test to rule out internal engine issues.

Solution

1. Preparation

Gather tools and parts.
Disconnect the negative battery terminal to prevent electrical shorts.
Allow the engine to cool completely before starting work.

2. Remove the Ignition Coil

Locate the ignition coil on the engine (typically on top of the engine near the spark plugs).
Remove any engine cover if necessary using a socket set.
Disconnect the electrical connector from the ignition coil by pressing the tab and pulling it off.
Remove the retaining bolts securing the ignition coil using a socket wrench.
Carefully pull the ignition coil straight out from the spark plug.

3. Inspect and Replace

Inspect the ignition coil for signs of wear or damage.
If a replacement is needed, ensure the new coil matches the specifications of the original.
Apply a small amount of dielectric grease to the inside of the ignition coil boot to ensure a good seal.
Install the new ignition coil by pushing it firmly onto the spark plug until it seats properly.
Reattach the retaining bolts and tighten to manufacturer specifications (typically around 7-10 Nm).

4. Reconnect Electrical Components

Reconnect the electrical connector to the ignition coil, ensuring it clicks into place securely.
Replace any engine cover removed during the process.

5. Final Checks

Reconnect the negative battery terminal.
Clear any trouble codes using the OBD-II scanner if applicable.