how to fix the engine light on my Toyota Corolla E170 (2013-2019) that keeps coming back

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

531 words

Problem Statement

Learn how to diagnose and fix the engine light issue in Toyota Corolla E170 (2013-2019). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components.
•Allow the engine to cool before handling any engine parts to prevent burns.

Symptoms

•Check engine light illuminated on the dashboard
•Engine running rough or misfiring
•Decreased fuel efficiency
•Unusual exhaust odors
•Performance issues during acceleration

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify specific fault codes.
2
Record the error codes and research them to determine potential causes.
3
Inspect the engine bay for visible issues such as loose or damaged wiring and hoses.
4
Check the fuel system for pressure using a fuel pressure gauge.
5
Inspect the ignition system components (spark plugs, ignition coils) for wear or damage.
6
Test the oxygen sensors and mass airflow sensor for proper function.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Fuel pressure gauge
•Torque wrench
•Oxygen sensor socket
•Multimeter

Parts Required

•Spark plugs
•Oxygen sensors (upstream and downstream)
•Electrical connectors or wiring as needed

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify specific fault codes.
2
Record the error codes and research them to determine potential causes.
3
Inspect the engine bay for visible issues such as loose or damaged wiring and hoses.
4
Check the fuel system for pressure using a fuel pressure gauge.
5
Inspect the ignition system components (spark plugs, ignition coils) for wear or damage.
6
Test the oxygen sensors and mass airflow sensor for proper function.

Solution

1. Preparation

Gather tools and parts required for the repair.
Disconnect the negative battery terminal to prevent electrical shorts.
Allow the engine to cool down if it has been running recently.

2. Address Faulty Components

A. Replace Spark Plugs

Remove the engine cover if applicable.
Disconnect the ignition coils by removing the connectors.
Use a socket wrench to remove the spark plugs.
Install new spark plugs, ensuring the gap is set to manufacturer specifications (0.043 inches).
Reconnect the ignition coils and engine cover.

B. Replace Faulty Oxygen Sensors

Locate the upstream and downstream oxygen sensors in the exhaust system.
Use an oxygen sensor socket to remove the faulty sensors.
Install the new oxygen sensors, ensuring proper torque (typically 30-35 ft-lbs).
Reconnect the electrical connectors to the sensors.

C. Repair or Replace Wiring

Inspect all wiring harnesses related to the engine management system for damage.
Repair any frayed wires with electrical tape or replace damaged wiring as necessary.
Ensure all connectors are clean and secure.

3. Clear Error Codes

Reconnect the negative battery terminal.
Use the OBD-II scanner to clear any stored error codes.
Start the engine and allow it to idle for a few minutes.