how to fix the ABS light on my Toyota Corolla E170 (2013-2019)

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

541 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix the ABS light issue on your 2013-2019 Toyota Corolla E170. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components.
•Ensure the vehicle is securely lifted and supported before working under it.

Symptoms

•ABS warning light illuminated on the dashboard
•Reduced braking performance or sensitivity
•Pulsating brake pedal during braking
•Unresponsive ABS system during hard braking
•Increased stopping distance

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify specific ABS-related trouble codes.
2
Inspect the ABS fuse for continuity and replace if blown.
3
Check the brake fluid level and top up if necessary.
4
Visually inspect ABS wheel speed sensors for damage or disconnection.
5
Test the resistance of the wheel speed sensors using a multimeter to ensure they are within specifications.
6
Examine the ABS control module for any signs of damage or corrosion.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Fuse puller
•Jack and jack stands
•Basic hand tools (socket set, screwdrivers)

Parts Required

•Replacement ABS fuse (if needed)
•Wheel speed sensor (if defective)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify specific ABS-related trouble codes.
2
Inspect the ABS fuse for continuity and replace if blown.
3
Check the brake fluid level and top up if necessary.
4
Visually inspect ABS wheel speed sensors for damage or disconnection.
5
Test the resistance of the wheel speed sensors using a multimeter to ensure they are within specifications.
6
Examine the ABS control module for any signs of damage or corrosion.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is on a level surface and parked securely.
Disconnect the negative battery terminal to prevent electrical shorts.

2. Inspect and Replace Fuses

Locate the fuse box under the dashboard or engine compartment.
Use a fuse puller to remove the ABS fuse.
Inspect the fuse for continuity; replace it with a new fuse of the same amperage if necessary.

3. Check Brake Fluid

Open the hood and locate the brake fluid reservoir.
Inspect the fluid level; if low, top up with the manufacturer-recommended brake fluid (DOT 3 or DOT 4).
Recheck the ABS light after topping up.

4. Inspect Wheel Speed Sensors

Lift the vehicle and securely support it on jack stands.
Locate the ABS wheel speed sensors at each wheel hub.
Disconnect the electrical connectors from each sensor.
Visually inspect the sensors and wiring for any damage or corrosion.
Clean any debris or dirt from the sensor area.

5. Test Wheel Speed Sensors

Reconnect the electrical connectors.
Use a multimeter to measure the resistance of each sensor; it should typically be between 1,000 to 2,500 ohms. Replace any sensor that is out of this range.

6. Reset ABS System

Reconnect the negative battery terminal.
Use an OBD-II scanner to clear any stored ABS trouble codes.
Take the vehicle for a test drive to ensure the ABS light does not re-illuminate.