how to fix the ABS light on my Toyota Corolla E170 (2013-2019)

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

555 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix the ABS light issue on your 2013-2019 Toyota Corolla E170. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery before working on electrical components.
•Ensure the vehicle is securely elevated if performing work underneath.

Symptoms

•ABS warning light illuminated on the dashboard
•Increased stopping distance during emergency braking
•Pulsation in the brake pedal when braking
•Reduced effectiveness of the braking system
•Brake system warning light may also be illuminated

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify specific ABS faults.
2
Inspect ABS fuses and relays to ensure they are not blown or damaged.
3
Check the ABS wheel speed sensors for proper connection and damage.
4
Inspect the brake fluid level and condition; refill or replace if necessary.
5
Visually inspect the wiring harness for the ABS system for fraying or disconnections.
6
Test the ABS pump and module for functionality if other components check out.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Screwdriver set
•Multimeter (optional for electrical testing)

Parts Required

•ABS wheel speed sensors (if replacement is necessary)
•Fuses/relays (if blown)
•Brake fluid (DOT 3 or DOT 4)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify specific ABS faults.
2
Inspect ABS fuses and relays to ensure they are not blown or damaged.
3
Check the ABS wheel speed sensors for proper connection and damage.
4
Inspect the brake fluid level and condition; refill or replace if necessary.
5
Visually inspect the wiring harness for the ABS system for fraying or disconnections.
6
Test the ABS pump and module for functionality if other components check out.

Solution

1. Preparation

Gather tools and parts needed.
Ensure the vehicle is on a flat surface and the ignition is off.
Disconnect the negative terminal of the battery for safety.

2. Address Fault Codes

Use the OBD-II scanner to retrieve and document fault codes.
Clear the codes and see if they return after a short drive.

3. Inspect and Replace ABS Wheel Speed Sensors

Locate the ABS wheel speed sensors at each wheel hub.
Disconnect the wiring harness from the sensor.
Remove the mounting bolt and pull the sensor out of the hub.
Inspect the sensor for damage. If damaged, install a new ABS wheel speed sensor.
Reconnect the wiring harness and secure the sensor in place.

4. Check and Replace Fuses/Relays

Locate the fuse box (refer to the owner's manual for the exact location).
Identify the ABS fuses and relays using the diagram in the fuse box cover.
Remove the fuses/relays and inspect them. Replace any that are blown or malfunctioning.

5. Verify Brake Fluid Level

Check the brake fluid reservoir located near the master cylinder.
If low, fill it with the recommended brake fluid (DOT 3 or DOT 4 as specified).
If the fluid is contaminated, perform a brake fluid flush.

6. Reconnect Battery and Test Drive

Reconnect the negative terminal of the battery.
Start the vehicle and perform a test drive to ensure the ABS light is no longer illuminated.