how to fix the ABS light on in my Toyota Corolla E170 (2013-2019)

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

4 min read

649 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix the ABS light issue in your Toyota Corolla E170 (2013-2019). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the brakes to cool before inspection or repair.

Symptoms

•ABS warning light illuminated on the dashboard
•Possible decrease in braking performance
•Increased stopping distance
•Brake pedal feels spongy or unresponsive
•Activation of the traction control warning light

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any ABS-related trouble codes.
2
Inspect the ABS fuse in the fuse box for any blown fuses.
3
Check the wheel speed sensors for damage or disconnection.
4
Inspect the ABS control module for any visible damage or corrosion.
5
Examine the brake fluid level and brake lines for leaks.
6
Test the ABS pump operation by applying the brakes and observing if the pump activates.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Fuse puller or pliers
•Socket set
•Torx screwdriver
•Multimeter
•Brake fluid funnel

Parts Required

•Replacement ABS fuse
•Wheel speed sensor(s) (if faulty)
•ABS control module (if damaged)
•Brake fluid (DOT 3 or DOT 4)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any ABS-related trouble codes.
2
Inspect the ABS fuse in the fuse box for any blown fuses.
3
Check the wheel speed sensors for damage or disconnection.
4
Inspect the ABS control module for any visible damage or corrosion.
5
Examine the brake fluid level and brake lines for leaks.
6
Test the ABS pump operation by applying the brakes and observing if the pump activates.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is on a flat surface and securely supported with jack stands.
Disconnect the negative battery terminal to prevent electrical short circuits.

2. Check & Replace ABS Fuse

Tools Required: Fuse puller or pliers
Locate the fuse panel, usually found under the dashboard or in the engine compartment.
Identify the ABS fuse using the diagram on the fuse cover.
Remove the ABS fuse and inspect it for continuity.
If blown, replace it with a fuse of the same amperage (usually 10-30A depending on the specific fuse).

3. Inspect Wheel Speed Sensors

Tools Required: Socket set, multimeter
Locate each wheel speed sensor at each wheel hub.
Disconnect the sensor wiring harness and visually inspect for any damage or corrosion.
Use a multimeter to test the sensor's resistance; it should typically be between 1,000 to 2,000 ohms.
If the sensor is faulty, replace it with a new one.

4. Inspect ABS Control Module

Tools Required: Socket set, Torx screwdriver
Locate the ABS control module, which is usually mounted near the brake master cylinder.
Visually inspect the module for any signs of leaks, corrosion, or damage.
If damaged, remove the module by unscrewing the mounting bolts and disconnecting the wiring harness.
Replace it with a compatible ABS control module.

5. Test and Refill Brake Fluid

Tools Required: Brake fluid (DOT 3 or DOT 4 as specified), funnel
Check the brake fluid reservoir level; if low, refill with the appropriate type of brake fluid.
Bleed the brake system to remove any air bubbles and ensure proper brake function.

6. Reconnect Battery and Test Drive

Reconnect the negative battery terminal.
Start the vehicle and check if the ABS light is still illuminated.
Take the vehicle for a test drive to confirm proper ABS functionality.