how to fix my Toyota Corolla E170 that makes a loud noise when turning

Toyota Corolla E170 (2013-2019)

Error Codes

3-5 hours

Time

medium

Difficulty

high

Severity

3 min read

569 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix loud noise when turning in Toyota Corolla E170. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Steering

Estimated Time

3-5 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components.
•Use jack stands to secure the vehicle when lifted.

Symptoms

•Loud grinding or clunking noise during turns
•Steering wheel feels loose or unresponsive
•Vibration in the steering wheel while turning
•Increased difficulty in turning the steering wheel
•Unusual tire wear patterns

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for any visible leaks in the power steering system.
3
Examine the condition of the steering rack and tie rod ends for wear or damage.
4
Inspect the CV joints and axles for any signs of wear or damage.
5
Test the suspension components, including struts and control arms, for any looseness or damage.
6
Check the wheel bearings for excessive play or noise.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Fluid pump
•Funnel
•Socket set
•Torque wrench
•Pry bar
•Axle puller
•Jack stands

Parts Required

•Power steering fluid
•Tie rod ends (if worn)
•CV joint or axle assembly (if damaged)
•Suspension components (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for any visible leaks in the power steering system.
3
Examine the condition of the steering rack and tie rod ends for wear or damage.
4
Inspect the CV joints and axles for any signs of wear or damage.
5
Test the suspension components, including struts and control arms, for any looseness or damage.
6
Check the wheel bearings for excessive play or noise.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface and the engine is turned off.
Disconnect the negative battery terminal for safety.

2. Inspect and Replace Power Steering Fluid

Tools Required: Fluid pump, funnel
Check the power steering fluid level; if low, refill with the manufacturer's recommended fluid.
If the fluid is dirty or contaminated, drain the system and replace with fresh fluid.

3. Replace Worn Steering Components

Tools Required: Socket set, torque wrench, pry bar
Remove the wheel and tire on the affected side to access the steering components.
Use a socket set to remove the tie rod end from the steering knuckle.
Inspect the tie rod end for wear and replace if necessary. Torque to manufacturer specifications.
If the steering rack is damaged, remove it by disconnecting it from the steering column and any mounting brackets. Replace with a new rack and ensure proper alignment.

4. Inspect and Replace CV Joints

Tools Required: Axle puller, socket set
Remove the axle nut and use an axle puller to detach the CV joint from the hub assembly.
Inspect the CV joint for tears or damage. If damaged, replace the CV joint or axle assembly.
Reinstall and torque the axle nut to the manufacturer's specifications.

5. Inspect and Replace Suspension Components

Tools Required: Jack stands, socket set
Use a jack to lift the vehicle and secure it with jack stands.
Inspect struts and control arms for damage. Replace any worn components as necessary.
Reassemble all components and ensure all bolts are torqued to specifications.