how to fix my Toyota Corolla E170 (2013-2019) that won’t go into gear

Toyota Corolla E170 (2013-2019)

Error Codes

4-8 hours

Time

hard

Difficulty

high

Severity

3 min read

534 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix transmission issues in Toyota Corolla E170 (2013-2019). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Transmission

Estimated Time

4-8 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Ensure the vehicle is securely lifted and supported before working underneath.

Symptoms

•Engine revs but vehicle does not move
•Difficulty in shifting gears or grinding noise
•Warning lights illuminated on the dashboard
•Clutch pedal feels spongy or has excessive travel
•Fluid leaks under the vehicle
•Unusual burning smell

Diagnostic Steps

1
Inspect the transmission fluid level and condition using the dipstick.
2
Check for any diagnostic trouble codes (DTCs) using an OBD-II scanner.
3
Examine the clutch system components for wear, including the master and slave cylinders.
4
Verify the operation of the clutch pedal and check for hydraulic leaks.
5
Inspect the shift linkage for any disconnections or damage.
6
Test the vehicle with a multimeter to check for electrical issues if applicable.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Wrench set
•Clutch alignment tool
•Brake bleeder kit

Parts Required

•Transmission fluid
•Clutch disc
•Pressure plate
•Flywheel (if worn)
•Clutch master/slave cylinder (if defective)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the transmission fluid level and condition using the dipstick.
2
Check for any diagnostic trouble codes (DTCs) using an OBD-II scanner.
3
Examine the clutch system components for wear, including the master and slave cylinders.
4
Verify the operation of the clutch pedal and check for hydraulic leaks.
5
Inspect the shift linkage for any disconnections or damage.
6
Test the vehicle with a multimeter to check for electrical issues if applicable.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a flat surface and the parking brake is engaged.
Disconnect the negative battery terminal to prevent electrical shorts.

2. Check and Replace Transmission Fluid

Tools Required: Socket set, funnel, container for fluid.
Remove the transmission fluid drain plug and allow the fluid to fully drain into a container.
Inspect the fluid for contamination or burnt smell.
If necessary, replace the fluid with the manufacturer-recommended type and refill using a funnel.
Torque the drain plug to the specified value (consult the service manual for specifics).

3. Inspect and Replace Clutch Components

Tools Required: Socket set, wrench set, clutch alignment tool.
Remove the transmission from the vehicle following manufacturer specifications.
Inspect the clutch disc, pressure plate, and flywheel for wear.
If any component is worn or damaged, replace with OEM parts.
Reassemble the transmission ensuring all bolts are torqued to specifications.

4. Bleed the Clutch System

Tools Required: Brake bleeder kit.
Locate the clutch slave cylinder and identify the bleed valve.
Attach the brake bleeder hose to the valve.
Open the bleed valve and pump the clutch pedal until air bubbles cease to appear in the fluid.
Close the bleed valve and top up the clutch fluid reservoir as needed.