how to fix my Toyota Corolla E170 (2013-2019) if the engine light is on after changing the oil?

Toyota Corolla E170 (2013-2019)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

3 min read

538 words

Problem Statement

Learn how to diagnose and fix the engine light issue after an oil change in your Toyota Corolla E170. Step-by-step guide with diagnostic procedures.

Affected Component

Engine

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Allow engine to cool before working on any hot components.

Symptoms

•Check engine light illuminated
•Possible oil leak under the vehicle
•Engine running rough or misfiring
•Low oil pressure warning light may be on
•Decreased engine performance
•Unusual engine noises (ticking or knocking)

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify specific trouble codes.
2
Check the engine oil level using the dipstick to ensure proper oil level.
3
Inspect the oil filter for proper installation and possible leaks.
4
Verify that the correct oil type and viscosity were used.
5
Inspect all connections and wiring around the oil pressure sensor.
6
Check for any oil spills or debris around the engine compartment that might interfere with sensors.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Oil filter wrench
•Torque wrench

Parts Required

•Engine oil (5W-20 or as specified)
•Oil filter (specific to Toyota Corolla E170)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify specific trouble codes.
2
Check the engine oil level using the dipstick to ensure proper oil level.
3
Inspect the oil filter for proper installation and possible leaks.
4
Verify that the correct oil type and viscosity were used.
5
Inspect all connections and wiring around the oil pressure sensor.
6
Check for any oil spills or debris around the engine compartment that might interfere with sensors.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface, and the engine is off and cool.
Disconnect the battery to avoid electrical shorts.

2. Addressing Oil Level and Quality

Sub-step 1: Remove the dipstick and wipe it clean.
Sub-step 2: Reinsert the dipstick fully, then remove it again to check the oil level.
Sub-step 3: If oil is low, add the recommended oil type (5W-20 or as specified in the owner’s manual) until the proper level is reached.

3. Inspecting the Oil Filter

Sub-step 1: Locate the oil filter and check for proper seating; there should be no gaps.
Sub-step 2: If the oil filter is loose or leaking, tighten it or replace it with a new one.
Sub-step 3: Make sure the oil filter's rubber O-ring is not stuck to the engine block.

4. Checking the Oil Pressure Sensor

Sub-step 1: Locate the oil pressure sensor and inspect the wiring for any signs of damage or disconnection.
Sub-step 2: Reconnect any loose wires and ensure the sensor is securely mounted.
Sub-step 3: If required, replace the oil pressure sensor using a socket wrench.

5. Resetting the Engine Light

Sub-step 1: Reconnect the battery.
Sub-step 2: Use the OBD-II scanner to reset the engine light if no fault codes are present after inspection and repairs.