how to fix my Toyota Corolla E170 (2013-2019) air conditioning that blows warm air?

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

581 words

Problem Statement

Learn how to diagnose and fix warm air blowing from the A/C in Toyota Corolla E170 (2013-2019). Step-by-step guide with tools and procedures.

Affected Component

HVAC

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always wear safety glasses when working with the A/C system.
•Disconnect the battery before working on electrical components.
•Allow the engine to cool before inspecting or working near the A/C components.

Symptoms

•Air conditioning blowing warm air
•A/C compressor not engaging
•Unusual noise from the A/C system
•A/C system cycling on and off frequently
•Foul odor from the vents
•Low A/C refrigerant level

Diagnostic Steps

1
Check the A/C system fuse for continuity using a multimeter.
2
Inspect the A/C compressor for any signs of damage or leaks.
3
Use an OBD-II scanner to check for any error codes related to the A/C system.
4
Measure the refrigerant pressure with a manifold gauge set to determine if it is within specification.
5
Inspect the A/C condenser for obstructions or debris blocking airflow.
6
Examine the cabin air filter for clogs that may restrict airflow.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•A/C manifold gauge set
•Multimeter
•Basic hand tools
•Vacuum pump

Parts Required

•A/C refrigerant (R-134a)
•A/C compressor (if faulty)
•Cabin air filter

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the A/C system fuse for continuity using a multimeter.
2
Inspect the A/C compressor for any signs of damage or leaks.
3
Use an OBD-II scanner to check for any error codes related to the A/C system.
4
Measure the refrigerant pressure with a manifold gauge set to determine if it is within specification.
5
Inspect the A/C condenser for obstructions or debris blocking airflow.
6
Examine the cabin air filter for clogs that may restrict airflow.

Solution

1. Preparation

Gather tools: A/C manifold gauge set, multimeter, basic hand tools, and a vacuum pump.
Ensure the vehicle is parked on a level surface and the engine is off.
Disconnect the negative battery terminal to prevent electrical shorts.

2. Check and Replace A/C Fuse

Locate the fuse box, typically found under the dashboard or in the engine compartment.
Identify the A/C fuse (refer to the owner’s manual for the specific fuse location).
Remove the fuse and inspect it for continuity; replace if blown.

3. Inspect and Replace Refrigerant

Connect the A/C manifold gauge set to the low and high-pressure service ports.
Start the engine and turn on the A/C to the maximum setting.
Check the pressure readings; if low, evacuate the system using a vacuum pump, then recharge with the correct type and amount of refrigerant (usually R-134a).
Monitor for leaks after recharging.

4. Test A/C Compressor Operation

With the A/C on, observe if the compressor clutch engages.
If it does not engage, test the compressor clutch coil using a multimeter.
Replace the A/C compressor if the coil is faulty or if the compressor is internally damaged.

5. Clean or Replace Cabin Air Filter

Locate the cabin air filter compartment, usually behind the glove box.
Remove the old filter and inspect it for dirt or blockage.
Clean the housing with a vacuum and replace with a new cabin air filter.