how to fix air conditioning issues in Toyota Corolla E170 (2013-2019)

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

589 words

Problem Statement

Learn how to diagnose and fix air conditioning issues in Toyota Corolla E170 (2013-2019). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

HVAC

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Ensure the system is properly evacuated before replacing the AC compressor to avoid refrigerant exposure.

Symptoms

•Air conditioning blows warm air
•Unusual noises from the AC compressor
•AC compressor does not engage
•Intermittent cooling
•Foul odor from the vents
•Reduced airflow from the vents

Diagnostic Steps

1
Check the refrigerant level using a manifold gauge set.
2
Inspect the AC compressor for any signs of damage or wear.
3
Examine the AC fuses and relays for continuity.
4
Test the AC switch and climate control module for functionality.
5
Look for any refrigerant leaks using a UV dye or leak detection spray.
6
Inspect the cabin air filter for clogs or dirt.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Manifold gauge set
•Refrigerant canister
•Safety goggles
•Gloves
•Screwdriver
•Socket set
•Torque wrench

Parts Required

•Refrigerant
•Cabin air filter
•AC compressor (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the refrigerant level using a manifold gauge set.
2
Inspect the AC compressor for any signs of damage or wear.
3
Examine the AC fuses and relays for continuity.
4
Test the AC switch and climate control module for functionality.
5
Look for any refrigerant leaks using a UV dye or leak detection spray.
6
Inspect the cabin air filter for clogs or dirt.

Solution

1. Preparation

Gather necessary tools and parts.
Disconnect the battery to ensure safety.
Allow the vehicle to cool down if it has been running.

2. Recharge Refrigerant

Tools Required: Manifold gauge set, refrigerant canister, safety goggles, gloves.
1. Connect the low-pressure side of the manifold gauge to the AC service port.
2. Start the engine and turn the AC to maximum cold.
3. Check the pressure; if low, attach the refrigerant canister to the manifold gauge.
4. Open the valve on the refrigerant canister and allow refrigerant to flow until the desired pressure is achieved.
5. Disconnect the manifold gauge and replace the service port cap.

3. Replace Cabin Air Filter

Tools Required: Screwdriver (if needed).
1. Access the cabin air filter compartment, usually located behind the glove box.
2. Remove the old cabin air filter by sliding it out.
3. Insert the new cabin air filter, ensuring it is oriented correctly.
4. Reassemble any components removed to access the filter.

4. Inspect and Replace AC Compressor (if necessary)

Tools Required: Socket set, torque wrench, AC compressor replacement part, refrigerant oil.
1. Disconnect the battery again.
2. Remove the drive belt from the AC compressor.
3. Disconnect electrical connectors and refrigerant lines from the compressor.
4. Unbolt the AC compressor from its mounting bracket.
5. Install the new compressor using the reverse of removal steps, applying the correct torque specifications.
6. Reconnect refrigerant lines and charge the system with refrigerant oil as per manufacturer specifications.

5. Test AC System Functionality

Tools Required: None.
1. Reconnect the battery.
2. Start the engine and turn on the AC to maximum.
3. Check if the AC compressor engages and if cool air is produced.
4. Monitor for any unusual noises or leaks.