how to clean the throttle body on Toyota Corolla E170 (2013-2019)

Toyota Corolla E170 (2013-2019)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

3 min read

526 words

Problem Statement

Learn how to clean the throttle body on a 2013-2019 Toyota Corolla E170. Step-by-step guide with symptoms, diagnostic steps, and tools required.

Affected Component

Engine

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components.
•Allow the engine to cool before beginning work on the throttle body.

Symptoms

•Rough idle
•Engine stalling
•Poor acceleration
•Check engine light illuminated
•Increased emissions

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to check for related issues.
2
Inspect the air intake system for any obvious obstructions or leaks.
3
Check the throttle response by manually opening the throttle plate.
4
Listen for unusual noises from the throttle body during engine operation.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Screwdrivers
•Cleaning cloths
•Throttle body cleaner
•Safety goggles
•Gloves

Parts Required

•Throttle body gasket (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Solution

1. Preparation

Tools Required: Socket set, screwdrivers, cleaning cloths, throttle body cleaner, safety goggles, gloves.
Sub-steps:
1. Park the vehicle on a level surface and engage the parking brake.
2. Disconnect the negative terminal of the battery to prevent electrical shorts.
3. Remove the engine cover if applicable (typically requires a socket or screwdriver).

2. Remove Air Intake Hose

Sub-steps:
1. Loosen the hose clamps securing the air intake hose to the throttle body using a screwdriver or socket.
2. Carefully disconnect the air intake hose from the throttle body.
3. Inspect the hose for any cracks or damage and replace if necessary.

3. Access Throttle Body

Sub-steps:
1. Disconnect any electrical connectors attached to the throttle body.
2. Remove the throttle body mounting bolts using a socket set (typically 10mm).
3. Gently pull the throttle body away from the intake manifold, ensuring no gaskets are damaged.

4. Clean Throttle Body

Sub-steps:
1. Spray throttle body cleaner onto a clean rag or directly onto the throttle body surfaces.
2. Wipe the interior of the throttle body, focusing on the throttle plate and intake passages, until clean.
3. Avoid using excessive force or abrasive materials to prevent damage to the throttle body.

5. Reassemble Components

Sub-steps:
1. Ensure the throttle body is clean and free of debris.
2. Place a new gasket if required, and carefully reattach the throttle body to the intake manifold.
3. Tighten the mounting bolts to the manufacturer’s specified torque (typically around 15 ft-lbs).
4. Reconnect any electrical connectors and the air intake hose, tightening the clamps securely.

6. Final Checks

Sub-steps:
1. Reconnect the negative terminal of the battery.
2. Start the engine and let it idle, checking for any abnormal noises or issues.
3. If needed, clear any error codes using the OBD-II scanner.