why does my Toyota Corolla E140 (2006-2013) make a hissing noise when turning

Toyota Corolla E140 (2006-2013)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

580 words

Problem Statement

Learn to diagnose and fix hissing noise when turning in Toyota Corolla E140. Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Steering

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Ensure the engine is turned off and cooled down before working on the vehicle.
•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before opening the power steering system.

Symptoms

•Hissing noise audible during turns
•Difficulty in steering or increased steering effort
•Fluid leaks around the power steering pump or lines
•Whining noise in addition to hissing when steering wheel is fully turned
•Unusual vibrations in the steering wheel

Diagnostic Steps

1
Inspect power steering fluid level and condition.
2
Check for leaks in power steering lines and pump.
3
Listen for hissing sound while turning the steering wheel with the engine running.
4
Examine the steering rack and pinion for wear or damage.
5
Inspect the serpentine belt for signs of wear or slippage.
6
Test the power steering pump for proper operation.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Fluid catch pan
•Power steering fluid
•Flashlight
•Rags

Parts Required

•Power steering pump (if defective)
•Serpentine belt (if worn)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect power steering fluid level and condition.
2
Check for leaks in power steering lines and pump.
3
Listen for hissing sound while turning the steering wheel with the engine running.
4
Examine the steering rack and pinion for wear or damage.
5
Inspect the serpentine belt for signs of wear or slippage.
6
Test the power steering pump for proper operation.

Solution

1. Preparation

Gather necessary tools and parts.
Tools Required: Socket set, fluid catch pan, power steering fluid, flashlight, rags.
Safety Warnings: Ensure the engine is turned off and cooled down before working on the vehicle.

2. Check Power Steering Fluid

Open the hood and locate the power steering reservoir.
Remove the cap and check the fluid level; it should be between the minimum and maximum marks.
If low, add the appropriate power steering fluid as specified in the owner’s manual.

3. Inspect for Leaks

With the engine running, turn the steering wheel side to side to pressurize the system.
Look for any signs of fluid leaks around the power steering pump, hoses, and steering rack.
If leaks are found, mark their locations for repair.

4. Replace Power Steering Pump (if necessary)

Disconnect the negative battery terminal.
Remove the serpentine belt from the power steering pump.
Disconnect the power steering lines from the pump (be prepared for fluid spillage).
Unbolt the pump from its mounting bracket and remove it.
Install the new power steering pump by reversing the removal steps.
Reconnect the power steering lines and refill the reservoir with fluid.

5. Inspect and Replace Serpentine Belt (if necessary)

Check the condition of the serpentine belt for cracks or wear.
If damaged, release tension from the belt tensioner and remove the old belt.
Install a new serpentine belt following the routing diagram under the hood.
Ensure it is properly tensioned.

6. Final Checks

Reconnect the negative battery terminal.
Start the engine and turn the steering wheel from lock to lock to bleed air out of the system.
Check fluid level again and top off if needed.