why does my Toyota Camry XV70 (2018-2024) make a clunking noise when turning

Toyota Camry XV80 (2025-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

517 words

Problem Statement

Diagnose and fix clunking noise when turning in Toyota Camry XV70 (2018-2024). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Always use jack stands when working under a vehicle.

Symptoms

•Clunking noise during left or right turns
•Increased vibration felt through the steering wheel
•Difficulty in steering or a loose steering feel
•Uneven tire wear
•Knocking sounds when going over bumps

Diagnostic Steps

1
Inspect the suspension components visually for any signs of damage or wear.
2
Check the steering linkage and joints for play or wear.
3
Lift the vehicle and support it securely; then check for any play in the wheel bearings.
4
Test drive the vehicle and listen for noises during turns and when driving over bumps.
5
Examine the CV joints (if applicable) for any visible damage or grease leakage.
6
Scan for any error codes using an OBD-II scanner that may indicate issues with the vehicle's systems.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•OBD-II scanner
•Jack and jack stands

Parts Required

•Tie rod ends (if worn)
•Ball joints (if worn)
•CV joint or axle assembly (if damaged)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the suspension components visually for any signs of damage or wear.
2
Check the steering linkage and joints for play or wear.
3
Lift the vehicle and support it securely; then check for any play in the wheel bearings.
4
Test drive the vehicle and listen for noises during turns and when driving over bumps.
5
Examine the CV joints (if applicable) for any visible damage or grease leakage.
6
Scan for any error codes using an OBD-II scanner that may indicate issues with the vehicle's systems.

Solution

1. Preparation

Gather necessary tools and parts.
Park the vehicle on a level surface and engage the parking brake.
Disconnect the battery to ensure safety while working on electrical components.

2. Inspect Suspension Components

Sub-steps:
- Remove the front wheel using a socket set.
- Visually inspect control arms, bushings, and struts for wear or damage.
- Check for any loose bolts and ensure they are torqued to manufacturer specifications (consult repair manual for torque values).

3. Check Steering Components

Sub-steps:
- Inspect the tie rod ends and ball joints for play or damage.
- If necessary, replace worn tie rod ends or ball joints by removing the retaining clips and nuts.
- Reassemble and torque all components to specifications.

4. Examine CV Joints

Sub-steps:
- If applicable, inspect the CV boots for tears or grease leaks.
- If the CV joints are damaged, remove the axle assembly by unbolting it from the hub and transmission.
- Replace the CV joint or axle assembly as needed, ensuring proper installation of new components.

5. Reassemble and Test

Sub-steps:
- Reinstall the front wheel, ensuring all lug nuts are torqued to specification.
- Reconnect the battery.
- Lower the vehicle and take it for a test drive to ensure the clunking noise has been resolved.