why does my Toyota Camry XV50 (2012-2017) make a clicking noise when turning?

Toyota Camry XV80 (2025-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

490 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix clicking noise when turning in Toyota Camry XV50 (2012-2017). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Ensure the vehicle is securely raised and supported before working underneath.

Symptoms

•Clicking noise when making sharp turns
•Noise increases with speed
•Vibration felt in the steering wheel
•Potential loss of steering responsiveness
•Uneven tire wear over time

Diagnostic Steps

1
Inspect the outer CV joints for any signs of wear or damage.
2
Check the inner CV joints for play or looseness.
3
Examine the wheel bearings for any signs of wear or noise.
4
Inspect suspension components (control arms, bushings) for damage or wear.
5
Test drive the vehicle to replicate the noise and determine the conditions under which it occurs.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Jack and jack stands
•Torque wrench
•Bearing puller

Parts Required

•CV joint assembly (outer or inner as needed)
•Wheel bearings (if applicable)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the outer CV joints for any signs of wear or damage.
2
Check the inner CV joints for play or looseness.
3
Examine the wheel bearings for any signs of wear or noise.
4
Inspect suspension components (control arms, bushings) for damage or wear.
5
Test drive the vehicle to replicate the noise and determine the conditions under which it occurs.

Solution

1. Preparation

Gather necessary tools and parts.
Park the vehicle on a level surface and engage the parking brake.
Disconnect the battery to ensure safety.

2. Lift the Vehicle

Use a jack to raise the front of the vehicle, then secure it with jack stands.
Remove the front wheels using a socket set.

3. Inspect and Replace CV Joints

Outer CV Joint Inspection:
- Remove the axle nut with a socket and breaker bar.
- Pull the CV axle free from the wheel hub if it’s damaged.
- Inspect the boot for tears and grease leakage. Replace the CV joint if needed.
Inner CV Joint Inspection:
- If the outer joint is fine, remove the axle from the transmission side.
- Check for play and inspect the inner boot.
- Replace the inner CV joint if damaged.

4. Inspect Wheel Bearings

Rotate the wheel hub by hand to listen for any abnormal noises.
If noise is present, replace the wheel bearings. Remove the hub, then use a bearing puller to replace them.

5. Reassemble and Lower Vehicle

Reinstall the CV axle or any replaced components.
Tighten the axle nut to the manufacturer’s torque specifications (typically around 150 ft-lbs).
Reattach the wheel, lower the vehicle, and reconnect the battery.