what is that noise from my Toyota Camry XV50 (2012-2017) rear wheel bearings

Toyota Camry XV70 (2018-2024)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

4 min read

627 words

Problem Statement

Learn how to diagnose and fix noise from rear wheel bearings in Toyota Camry XV50 (2012-2017). Step-by-step guide with symptoms and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components.
•Allow the vehicle to cool before working on brake components.

Symptoms

•Grinding or humming noise from the rear wheels, especially during turns
•Vibration felt through the steering wheel or chassis
•Uneven tire wear on the rear tires
•Increased road noise at higher speeds
•Noise increases with vehicle speed

Diagnostic Steps

1
Inspect the rear wheel bearings by lifting the vehicle and checking for excessive play in the wheel.
2
Rotate the rear wheels by hand to listen for any grinding or roughness in the bearings.
3
Check for any visible signs of damage or wear on the rear wheel assemblies.
4
Use a stethoscope or a mechanic's listening device to pinpoint the noise when the vehicle is in motion.
5
Verify the condition of the rear tires for uneven wear patterns or damage.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack and jack stands
•Lug wrench
•Socket set
•Torque wrench
•Bearing puller
•Grease

Parts Required

•New rear wheel bearing assembly
•New axle nut (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the rear wheel bearings by lifting the vehicle and checking for excessive play in the wheel.
2
Rotate the rear wheels by hand to listen for any grinding or roughness in the bearings.
3
Check for any visible signs of damage or wear on the rear wheel assemblies.
4
Use a stethoscope or a mechanic's listening device to pinpoint the noise when the vehicle is in motion.
5
Verify the condition of the rear tires for uneven wear patterns or damage.

Solution

1. Preparation

Tools Required: Jack and jack stands, lug wrench, wheel chocks, socket set, torque wrench, bearing puller, grease, and a new wheel bearing assembly.
Ensure the vehicle is parked on a level surface and the ignition is off.
Disconnect the battery (optional for safety).

2. Lift and Remove the Wheel

Use the lug wrench to loosen the lug nuts on the rear wheel.
Raise the vehicle using a jack and secure it with jack stands.
Remove the lug nuts and take off the rear wheel.

3. Remove the Brake Components

Tools Required: Socket set
Remove the caliper by unbolting it from the bracket, then hang it out of the way using a wire or bungee cord (do not let it dangle by the brake line).
Remove the brake rotor by removing any retaining screws and sliding it off the hub.

4. Remove the Bearing Hub Assembly

Tools Required: Bearing puller
Remove the axle nut (if applicable) using a socket wrench.
Disconnect any ABS sensor wiring if present.
Use a bearing puller to carefully extract the rear wheel bearing hub assembly from the axle.

5. Install New Wheel Bearings

Clean the hub mounting surface on the axle.
Tools Required: Torque wrench
Install the new wheel bearing hub assembly in reverse order of removal, ensuring it is seated correctly.
Tighten the axle nut to the manufacturer’s specified torque value (typically around 150 ft-lbs).
Reconnect any ABS sensor wiring.

6. Reinstall Brake Components and Wheel

Reinstall the brake rotor and caliper.
Secure the caliper with the appropriate bolts.
Place the wheel back on and hand-tighten the lug nuts.
Lower the vehicle and torque the lug nuts to the manufacturer’s specifications (usually around 76 ft-lbs).