FAULTBASE
Error CodesASKCars
© 2026 FAULTBASE
All rights reserved.
v2.0.0 • Production
ContactPrivacyImpressum
How do I diagnose a malfunctioning throttle position sensor in my Toyota Camry XV70? - Toyota Camry
Home/Cars/Toyota/Camry/XV70 (2018-2024)/How do I diagnose a malfunctioning throttle position sensor in my Toyota Camry XV70?

How do I diagnose a malfunctioning throttle position sensor in my Toyota Camry XV70?

Toyota Camry XV70 (2018-2024)

Error Codes
2-3 hours
Time
medium
Difficulty
medium
Severity
Navigation
ProblemSymptomsDiagnosisSolution
ProblemSymptomsDiagnosisSolution
4 min read
736 words

Problem Statement

Learn how to diagnose and replace a malfunctioning throttle position sensor in your Toyota Camry XV70 (2018-2024). Step-by-step guide with symptoms, tools, and diagnostic steps.

Affected Component
Throttle Position Sensor
Estimated Time
2-3 hours

Symptoms

  • •Poor Engine Performance
  • •Check Engine Light
  • •Increased Fuel Consumption
  • •Erratic Engine Behavior
  • •Inconsistent RPMs

Diagnostic Steps

  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  6. 6
  7. 7
  8. 8
  9. 9
  10. 10
  11. 11

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

  • ✓Test the affected component to ensure it functions correctly
  • ✓Check for any error codes or warning lights
  • ✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

  • •Follow the manufacturer's recommended maintenance schedule
  • •Address warning signs early before they develop into major issues
  • •Use quality parts and fluids recommended for your vehicle
  • •Keep detailed records of all repairs and maintenance

Tools & Equipment Required

  • •OBD-II Scanner
  • •Multimeter
  • •Screwdrivers (flathead and Phillips)
  • •Socket set (including ratchet)
  • •Torque wrench
  • •Wiring diagram (optional)

Additional Information

Affected Component
Throttle Position Sensor
Estimated Time
2-3 hours
Difficulty
medium
Severity
medium
Tools Required
6 items

Related Faults

Loading...

Share this solution

Comments

Sign in to share your thoughts

Sign In

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnosing a Malfunctioning Throttle Position Sensor in a Toyota Camry XV70 (2018-2024)

Required Tools
  • OBD-II Scanner
  • Multimeter
  • Screwdrivers (flathead and Phillips)
  • Socket set (including ratchet)
  • Torque wrench
  • Wiring diagram (optional)
Step 1: Initial Inspection
  1. Visual Inspection: Open the hood and visually inspect the throttle body and TPS for any obvious signs of damage or disconnection.
  2. Check Connections: Ensure that the electrical connectors to the TPS are secure and free from corrosion.
Step 2: Scan for Diagnostic Trouble Codes (DTCs)
  1. Connect OBD-II Scanner: Plug the OBD-II scanner into the vehicle's diagnostic port, typically located under the dashboard.
  2. Read Codes: Turn the ignition to the "On" position without starting the engine and scan for any stored trouble codes.
    • Look specifically for codes related to the throttle position sensor (e.g., P0120, P0121).
Step 3: Testing the TPS with a Multimeter
  1. Disconnect the TPS: Ensure the ignition is off, then unplug the TPS connector.
  2. Set the Multimeter: Set your multimeter to the DC voltage setting.
  3. Identify TPS Pins: Refer to the wiring diagram to identify the correct pins (usually VCC, Signal, and Ground).
  4. Test Voltage Supply:
    • Connect the multimeter's positive lead to the VCC pin and the negative lead to ground.
    • Turn the ignition to the "On" position (do not start the engine) and check for the specified voltage (usually around 5V).
  5. Test Signal Output:
    • While still connected, back-probe the signal pin with the positive lead and ground with the negative lead.
    • Slowly move the throttle from closed to fully open and check the voltage reading. It should vary smoothly from around 0.5V to about 4.5V (check the specific values for your model).
Step 4: Evaluate Readings
  • Faulty TPS: If the voltage does not change smoothly or is outside the specified range, the TPS may be faulty and require replacement.
  • No Voltage Supply: If there is no voltage supply to the TPS, there may be an issue with the wiring or the Engine Control Unit (ECU).
Step 5: Inspect Wiring and Connectors
  • If the TPS readings were inconsistent, inspect the wiring harness for damage, shorts, or open circuits.
  • Repair or replace any damaged wiring or connectors.
Repair Instructions
Step 1: Replacement of the Throttle Position Sensor
  1. Disconnect Battery: Disconnect the negative terminal of the battery to prevent electrical shorts.
  2. Remove the Throttle Body (if necessary):
    • Depending on the layout, you may need to remove the throttle body to access the TPS. Remove any air intake components and electrical connectors attached to the throttle body.
    • Use a socket set to remove the bolts securing the throttle body to the intake manifold. Carefully lift it out.
  3. Remove the TPS:
    • Locate the TPS on the throttle body. Use a screwdriver to remove the screws securing the TPS.
    • Gently pull off the TPS from its mounting position.
Step 2: Install New TPS
  1. Install New TPS:
    • Position the new TPS onto the throttle body and secure it with screws.
    • Ensure it is aligned properly with the throttle shaft.
  2. Reconnect Components:
    • Reattach the throttle body to the intake manifold, ensuring proper alignment and sealing.
    • Reconnect any air intake components and electrical connections.
  3. Reconnect Battery: Reconnect the negative terminal of the battery.
Step 3: Final Testing
  1. Clear DTCs: Use the OBD-II scanner to clear any stored trouble codes from the ECU.
  2. Test Drive: Start the engine and take the vehicle for a test drive to ensure proper throttle response and performance.
  3. Recheck Codes: After the test drive, scan for any new codes to ensure that the issue has been resolved.
Conclusion

If the symptoms persist after the replacement of the throttle position sensor, further diagnosis may be necessary, potentially involving the ECU or other related components. Always refer to the manufacturer’s service manual for specific procedures and specifications.