how to fix the sunroof not closing properly on my Tesla Model S Plaid/Refresh (2021-present)?

Tesla Model S Plaid/Refresh (2021-present)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

3 min read

490 words

Problem Statement

Learn how to diagnose and fix sunroof issues in Tesla Model S Plaid. Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Body/Interior

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the vehicle from the charging station before working on electrical components.

Symptoms

•Sunroof does not fully close or remains partially open
•Unusual noises during closing attempt (grinding or clicking)
•Sunroof opens unexpectedly or reverses direction
•Water leakage into the cabin
•Warning message on the vehicle display about the sunroof

Diagnostic Steps

1
Inspect the sunroof for any visible obstructions or debris in the track.
2
Check the sunroof seal for any signs of wear or damage.
3
Use the vehicle's touchscreen to run the sunroof calibration procedure.
4
Scan the vehicle for any error codes related to the sunroof system using an OBD-II scanner.
5
Test the sunroof operation through the controls to confirm whether the issue persists.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Soft brush
•Cloth
•Trim removal tools
•Adhesive (if necessary)

Parts Required

•New sunroof seal (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the sunroof for any visible obstructions or debris in the track.
2
Check the sunroof seal for any signs of wear or damage.
3
Use the vehicle's touchscreen to run the sunroof calibration procedure.
4
Scan the vehicle for any error codes related to the sunroof system using an OBD-II scanner.
5
Test the sunroof operation through the controls to confirm whether the issue persists.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is in a safe working environment.
Disconnect the vehicle from the charging station if applicable.

2. Inspect and Clean the Sunroof Track

Sub-steps:
1. Open the sunroof fully.
2. Use a soft brush or cloth to remove any debris or dirt from the sunroof track.
3. Wipe down the sunroof seal with a damp cloth to remove any contaminants.
Tools Required: Soft brush, cloth

3. Check and Replace the Sunroof Seal (if needed)

Sub-steps:
1. Carefully inspect the sunroof seal for cracks or tears.
2. If damaged, remove the old seal by gently pulling it away from the sunroof frame.
3. Clean the area where the seal was attached.
4. Apply a new sunroof seal, ensuring a tight fit around the entire perimeter.
Parts Required: New sunroof seal
Tools Required: Trim removal tools, adhesive (if required)

4. Calibrate the Sunroof

Sub-steps:
1. Access the Tesla touchscreen and go to “Controls.”
2. Navigate to “Service” and select “Sunroof Calibration.”
3. Follow on-screen instructions to recalibrate the sunroof.
Tools Required: None

5. Test Sunroof Operation

Sub-steps:
1. Operate the sunroof using the touchscreen controls.
2. Ensure the sunroof closes completely without any obstruction or unusual noises.
Tools Required: None