my Tesla Model 3 Highland (2024-present) windshield wipers won’t turn off, what could be the issue?

Tesla Model 3 Highland (2024-present)

Error Codes

1-3 hours

Time

medium

Difficulty

medium

Severity

3 min read

495 words

Problem Statement

Learn how to diagnose and fix windshield wipers that won't turn off in Tesla Model 3 Highland. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Electrical

Estimated Time

1-3 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems to prevent shock or short circuits.
•Allow the vehicle to cool down before working on components near the engine or electrical systems.

Symptoms

•Wipers continuously operate even when switched off
•Wiper control stalk unresponsive
•Intermittent wiper function not working
•Possible warning messages on the dashboard
•Electrical system anomalies (e.g., flickering lights)

Diagnostic Steps

1
Check the windshield wiper settings on the touchscreen interface for any erroneous configurations.
2
Inspect the wiper control stalk for physical damage or obstructions.
3
Use an OBD-II scanner to check for any fault codes related to the wiper system.
4
Verify the condition of the wiper relay by removing it and testing continuity.
5
Inspect wiring harnesses and connectors for signs of damage or corrosion.
6
Test the wiper motor for proper operation by applying direct power.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Torx screwdriver
•Wire strippers and connectors

Parts Required

•Wiper control stalk (if faulty)
•Wiper relay (if defective)
•Wiper motor (if not functioning)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the windshield wiper settings on the touchscreen interface for any erroneous configurations.
2
Inspect the wiper control stalk for physical damage or obstructions.
3
Use an OBD-II scanner to check for any fault codes related to the wiper system.
4
Verify the condition of the wiper relay by removing it and testing continuity.
5
Inspect wiring harnesses and connectors for signs of damage or corrosion.
6
Test the wiper motor for proper operation by applying direct power.

Solution

1. Preparation

Gather tools and parts.
Disconnect the vehicle’s 12V battery to ensure safety during repairs.

2. Inspect and Test the Wiper Control Stalk

Remove the steering column cover using a Torx screwdriver.
Disconnect the electrical connector from the wiper control stalk.
Test the stalk for continuity using a multimeter; replace if faulty.

3. Check and Replace the Wiper Relay

Locate the fuse box (usually under the dashboard) and remove the wiper relay.
Test the relay with a multimeter for continuity; replace if defective.
Reinstall the new relay securely in the fuse box.

4. Inspect Wiring and Connectors

Visually inspect all wiring and connectors related to the wiper system for damage or corrosion.
Repair or replace any damaged wires or connectors as needed.

5. Test the Wiper Motor

Disconnect the wiper motor from the vehicle.
Apply direct power from a 12V source to test the motor's operation; replace if it does not operate.

6. Reassemble

Reattach all components in reverse order of disassembly.
Reconnect the vehicle’s 12V battery.
Ensure all components are secure and correctly positioned.