why is my Tesla Outback 5th Generation (2015-2019) making a knocking noise when I accelerate

Subaru Outback 5th Generation (2015-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

495 words

Problem Statement

Learn how to diagnose and fix knocking noise during acceleration in Tesla Outback 5th Generation (2015-2019). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Ensure the vehicle is securely supported on jack stands before working underneath.

Symptoms

•Knocking noise increases with acceleration
•Noise is more pronounced when turning
•Vibration felt through the steering wheel or floor
•Possible loss of power during acceleration
•Abnormal tire wear may be observed

Diagnostic Steps

1
Inspect the undercarriage for loose or damaged components.
2
Check the engine and transmission mounts for wear or damage.
3
Test the CV joints for wear by performing a visual inspection and listening for noise during turns.
4
Examine the suspension components, including struts and control arms, for any signs of damage.
5
Use a stethoscope or mechanic's listening device to pinpoint the source of the noise during acceleration.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Jack and jack stands
•Pry bar

Parts Required

•Engine and transmission mounts (if damaged)
•CV axle (if wear is found)
•Suspension components (if damaged)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the undercarriage for loose or damaged components.
2
Check the engine and transmission mounts for wear or damage.
3
Test the CV joints for wear by performing a visual inspection and listening for noise during turns.
4
Examine the suspension components, including struts and control arms, for any signs of damage.
5
Use a stethoscope or mechanic's listening device to pinpoint the source of the noise during acceleration.

Solution

1. Preparation

Gather necessary tools and parts.
Park the vehicle on a level surface and engage the parking brake.
Disconnect the battery to ensure safety while working on electrical components.

2. Inspect and Secure Engine and Transmission Mounts

Tools Required: Socket set, torque wrench
Sub-steps:
1. Locate the engine and transmission mounts.
2. Inspect for cracks, wear, or soft spots in the rubber.
3. Tighten any loose bolts to manufacturer specifications (refer to the service manual for torque values).
4. Replace any damaged mounts with new ones.

3. Check and Replace CV Joints if Necessary

Tools Required: Jack and jack stands, socket set
Sub-steps:
1. Raise the vehicle and secure it on jack stands.
2. Remove the wheels to access the CV joints.
3. Inspect the CV boots for tears or leaks, and check for play in the joints.
4. If wear is found, remove the CV axle and replace with a new unit.
5. Reinstall the wheels and lower the vehicle.

4. Inspect Suspension Components

Tools Required: Socket set, pry bar
Sub-steps:
1. Inspect struts, control arms, and bushings for damage or wear.
2. Use a pry bar to check for excessive play in the bushings and joints.
3. Replace any worn or damaged components.
4. Ensure all bolts are torqued to manufacturer specifications.