Tesla Outback 5th Generation (2015-2019) power windows won't go down what to check

Subaru Outback 5th Generation (2015-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

500 words

Problem Statement

Learn how to diagnose and fix power windows not working in Tesla Outback 5th Generation (2015-2019). Step-by-step guide with tools and tips.

Affected Component

Electrical

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems
•Allow the vehicle to cool before handling components

Symptoms

•Power window switches are unresponsive
•No sound when pressing window switches
•Other electrical components functioning normally
•Windows may be stuck in the closed position
•Possible flickering of the window control panel lights

Diagnostic Steps

1
Inspect the fuse related to the power windows using the vehicle’s fuse box diagram
2
Use a multimeter to check for voltage at the power window switch
3
Examine the wiring harness and connections for any visible damage or loose connections
4
Test the operation of the window motor by applying direct power from the battery
5
Use an OBD-II scanner to check for any stored error codes related to the window control system
6
Inspect the window regulator for mechanical failure or obstructions

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Multimeter
•Fuse puller
•Screwdriver set
•Wire connectors
•Electrical tape

Parts Required

•Power window fuse (if blown)
•Window motor (if faulty)
•Window regulator (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the fuse related to the power windows using the vehicle’s fuse box diagram
2
Use a multimeter to check for voltage at the power window switch
3
Examine the wiring harness and connections for any visible damage or loose connections
4
Test the operation of the window motor by applying direct power from the battery
5
Use an OBD-II scanner to check for any stored error codes related to the window control system
6
Inspect the window regulator for mechanical failure or obstructions

Solution

1. Preparation

Gather tools: multimeter, fuse puller, screwdriver set, wire connectors, and electrical tape.
Ensure the vehicle is parked on a flat surface and the ignition is off.

2. Check and Replace Fuse

Locate the fuse box and identify the power window fuse.
Use a fuse puller to remove the fuse and inspect it for continuity.
If the fuse is blown, replace it with a new one of the same amperage (refer to the owner's manual for specifications).

3. Inspect Wiring and Connections

Remove the door panel using a screwdriver and trim removal tools.
Visually inspect the wiring harness for frays or breaks.
Tighten any loose connections and repair damaged wires with solder or wire connectors.

4. Test Window Motor

Disconnect the window motor from the wiring harness.
Use jumper wires to connect the motor directly to the battery (positive to positive, negative to negative).
If the motor does not operate, it may need replacement.

5. Replace Window Regulator (if necessary)

If the window motor is functional but the window does not move, the regulator may be faulty.
Remove the window motor and regulator assembly.
Install a new regulator by reversing the removal steps and ensure all bolts are torqued to manufacturer specifications.