my Tesla Outback 5th Generation (2015-2019) makes a clicking noise when turning, what could it be?

Subaru Outback 5th Generation (2015-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

527 words

Problem Statement

Learn how to diagnose and fix clicking noise when turning in Tesla Outback 5th Generation. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Use jack stands to securely support the vehicle while working underneath.

Symptoms

•Clicking noise during turns
•Possible vibration in the steering wheel
•Difficulty steering or a feeling of looseness
•Unusual tire wear patterns
•No warning lights illuminated on the dashboard

Diagnostic Steps

1
Inspect the CV joints for wear or damage by visually examining the rubber boots.
2
Check the wheel bearings for play by lifting the vehicle and shaking the wheel.
3
Examine the suspension components for any loose or damaged parts.
4
Test the power steering fluid level and condition.
5
Scan for any error codes using an OBD-II scanner to rule out electrical issues.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Jack and jack stands
•Bearing puller

Parts Required

•CV joint or axle assembly (if damaged)
•Wheel bearings (if worn)
•Suspension components (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the CV joints for wear or damage by visually examining the rubber boots.
2
Check the wheel bearings for play by lifting the vehicle and shaking the wheel.
3
Examine the suspension components for any loose or damaged parts.
4
Test the power steering fluid level and condition.
5
Scan for any error codes using an OBD-II scanner to rule out electrical issues.

Solution

1. Preparation

Gather tools and parts needed for the repair.
Ensure the vehicle is parked on a level surface and the engine is off.
Safety: Disconnect the battery to prevent electrical shorts.

2. Inspect and Replace CV Joints

Sub-steps:
1. Raise the vehicle using jack stands to access the front wheels.
2. Remove the wheel by loosening the lug nuts using a socket set.
3. Inspect the CV joint boots; look for cracks or grease leaks.
4. If damaged, remove the axle nut with a socket and breaker bar.
5. Detach the CV axle from the hub assembly and remove it from the vehicle.
6. Replace the CV joint or axle assembly if damaged, ensuring proper orientation.
7. Reinstall the axle and tighten the axle nut to the manufacturer's torque specification (typically around 150 ft-lbs).

3. Check and Replace Wheel Bearings

Sub-steps:
1. While the axle is removed, inspect the wheel bearings for excessive play.
2. If worn, remove the bearing assembly using a bearing puller.
3. Install the new bearing and ensure it is seated correctly.
4. Reassemble the wheel and tighten all components to the specified torque.

4. Inspect and Repair Suspension Components

Sub-steps:
1. Check all suspension components for damage (control arms, ball joints, etc.).
2. Replace any worn or damaged parts, ensuring proper alignment upon reinstallation.
3. Torque all suspension bolts to factory specifications.