my Tesla Outback 5th Generation (2015-2019) is making a clicking noise when I accelerate what's happ...

Subaru Outback 5th Generation (2015-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

562 words

Problem Statement

Learn how to diagnose and fix clicking noise during acceleration in Tesla Outback 5th Generation. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Ensure the vehicle is securely supported on jack stands before working underneath.

Symptoms

•Clicking noise increases with acceleration
•Possible vibrations felt through the drivetrain
•Noise may change with steering input
•Loss of power during acceleration
•Check engine light may illuminate

Diagnostic Steps

1
Inspect the vehicle for any visible signs of damage to the undercarriage or drivetrain components.
2
Check the condition of the CV joints and axles for any signs of wear or damage.
3
Conduct a test drive to determine if the noise is related to speed, acceleration, or steering.
4
Scan for error codes using an OBD-II scanner to identify any related electronic issues.
5
Inspect suspension components, including bushings and struts, for wear or looseness.
6
Examine wheel bearings for play or noise while rotating the wheel.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Jack and jack stands
•Lug wrench
•Socket set
•Torque wrench
•Bearing press

Parts Required

•CV axle
•Wheel bearing

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the vehicle for any visible signs of damage to the undercarriage or drivetrain components.
2
Check the condition of the CV joints and axles for any signs of wear or damage.
3
Conduct a test drive to determine if the noise is related to speed, acceleration, or steering.
4
Scan for error codes using an OBD-II scanner to identify any related electronic issues.
5
Inspect suspension components, including bushings and struts, for wear or looseness.
6
Examine wheel bearings for play or noise while rotating the wheel.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface and engage the parking brake.
Disconnect the battery to avoid electrical shocks.

2. Inspect and Replace CV Joints

Raise the Vehicle: Use a jack to lift the vehicle and secure it with jack stands.
Remove Wheels: Use a lug wrench to remove the wheels for access to the CV joints.
Inspect CV Joints: Check the boot for tears and the joint for excessive play. If damaged, proceed to replace.
Remove CV Axle:
- Remove the axle nut using a socket and breaker bar.
- Disconnect the lower control arm to free the CV axle.
Install New CV Axle:
- Align the new CV axle and insert it into the hub.
- Reattach the lower control arm.
- Torque the axle nut to manufacturer specifications (typically around 150 ft-lbs).
Reinstall Wheels: Put the wheels back on and lower the vehicle.

3. Inspect and Replace Wheel Bearings (if necessary)

Remove Wheel Again: If needed, repeat the wheel removal process.
Check for Bearing Play: Spin the wheel and listen for grinding noises. If present, proceed to replace.
Remove Hub Assembly: Depending on the model, you may need to remove the brake caliper, rotor, and hub assembly.
Install New Bearing: Press in the new bearing using a bearing press. Ensure it is seated properly.
Reassemble: Reinstall the hub assembly, rotor, and brake caliper. Torque all bolts to manufacturer specifications.