how to troubleshoot the remote start issues on Tesla Outback 4th Generation (2010-2014)

Subaru Outback 4th Generation (2010-2014)

Error Codes

1-2 hours

Time

medium

Difficulty

high

Severity

3 min read

475 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to troubleshoot and fix remote start issues in 2010-2014 Subaru Outback. Step-by-step guide with diagnostic steps and solutions.

Affected Component

Electrical

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems to prevent shocks or shorts.

Symptoms

•Remote start button does not respond when pressed
•Check engine light illuminated on the dashboard
•Engine cranks but does not start
•Vehicle starts only when using the key fob in the ignition
•Intermittent issues with remote locking/unlocking

Diagnostic Steps

1
Check the battery voltage of the key fob using a multimeter.
2
Inspect the key fob for physical damage or worn buttons.
3
Scan the vehicle's OBD-II system for any error codes related to the remote start system.
4
Verify that the vehicle is in park or neutral, as remote start will not function if the transmission is in gear.
5
Test the remote start feature with a different key fob if available.
6
Check the status of the vehicle's security system and any aftermarket alarm systems.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Small flathead screwdriver
•Basic socket set

Parts Required

•Key fob battery (CR2032)
•Electrical connectors (if wire repairs are needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the battery voltage of the key fob using a multimeter.
2
Inspect the key fob for physical damage or worn buttons.
3
Scan the vehicle's OBD-II system for any error codes related to the remote start system.
4
Verify that the vehicle is in park or neutral, as remote start will not function if the transmission is in gear.
5
Test the remote start feature with a different key fob if available.
6
Check the status of the vehicle's security system and any aftermarket alarm systems.

Solution

1. Preparation

Gather all necessary tools and parts.
Ensure the vehicle is parked on a level surface.
Disconnect the battery to prevent any electrical issues during repairs.

2. Key Fob Check

Inspect Battery:
- Open the key fob using a small flathead screwdriver.
- Remove the battery and replace it with a new one (usually CR2032).
- Reassemble the fob and test the remote start function.

3. System Reset

Perform a System Reset:
- Reconnect the vehicle's battery.
- Turn the ignition to the ON position without starting the engine.
- Wait for 10 seconds and then turn the ignition off.
- Test the remote start feature again.

4. Wiring Inspection

Inspect Wiring:
- Remove the panel covering the keyless entry module (usually located under the dashboard).
- Check all wiring connections for corrosion or loose connections.
- Repair any damaged wires as necessary.

5. Security System Check

Examine Security Features:
- If the vehicle has an aftermarket alarm, ensure it is compatible with the remote start system.
- Consult the alarm system's manual for any specific troubleshooting steps.