why does my Renault Clio V (2019-Present) shake when I brake

Renault Clio V (2019-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

489 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix shaking when braking in Renault Clio V (2019-Present). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always ensure the vehicle is securely supported on jack stands before working underneath.
•Allow brakes to cool to prevent burns when handling components.

Symptoms

•Vibration felt in the steering wheel during braking
•Pulsation in the brake pedal when applied
•Uneven wear on brake pads or rotors
•Noise (grinding or squeaking) while braking
•Increased stopping distance

Diagnostic Steps

1
Inspect brake rotor surfaces for warping or uneven wear.
2
Check brake pad thickness and condition for wear.
3
Examine brake calipers for proper function and possible sticking.
4
Inspect suspension components (e.g., control arms, bushings) for wear.
5
Test wheel alignment and balance to rule out additional causes.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack and jack stands
•Lug wrench
•Torque wrench
•Dial indicator (for rotor inspection)
•Brake cleaner and lubricants

Parts Required

•Brake rotors (if warped)
•Brake pads (if worn)
•Brake caliper components (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect brake rotor surfaces for warping or uneven wear.
2
Check brake pad thickness and condition for wear.
3
Examine brake calipers for proper function and possible sticking.
4
Inspect suspension components (e.g., control arms, bushings) for wear.
5
Test wheel alignment and balance to rule out additional causes.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface.
Wear safety gloves and goggles.

2. Remove Wheel

Sub-steps:
1. Loosen lug nuts on the wheel while the vehicle is still on the ground.
2. Lift the vehicle using a jack and secure it with jack stands.
3. Completely remove the lug nuts and take off the wheel.

3. Inspect and Replace Brake Components

Sub-steps:
1. Inspect brake rotors for warping using a dial indicator. Replace if warped beyond the manufacturer's specifications (usually over 0.002 inches).
2. Measure brake pads for thickness; replace if they are below the minimum specification (usually around 3mm).
3. If calipers are sticking, remove the caliper from the bracket, and inspect the sliding pins and piston. Clean and lubricate as necessary or replace if damaged.

4. Reinstall Components

Sub-steps:
1. Install new brake pads and rotors, ensuring they are seated correctly.
2. Reattach the caliper and ensure it is properly secured with the manufacturer's torque specifications.
3. Reinstall the wheel and hand-tighten lug nuts.

5. Lower Vehicle and Finalize

Sub-steps:
1. Lower the vehicle from the jack stands.
2. Tighten lug nuts to the manufacturer-recommended torque specifications.
3. Pump the brake pedal a few times to seat the brake pads against the rotors.