my Renault Clio V (2019-Present) makes a knocking sound when accelerating, what's the cause?

Renault Clio V (2019-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

554 words

Problem Statement

Learn how to diagnose and fix knocking sound during acceleration in Renault Clio V. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Ensure the vehicle is securely supported by jack stands before working underneath it.

Symptoms

•Knocking or clunking noise when accelerating
•Noise may increase with speed
•Possible vibration through the floor or steering wheel
•Loss of power or hesitation during acceleration
•Unusual wear on tires (in some cases)

Diagnostic Steps

1
Inspect the undercarriage for any loose or damaged components.
2
Verify engine mounts for wear or damage.
3
Check the condition of the driveshaft and CV joints for any signs of wear or damage.
4
Examine the suspension components, including control arms and bushings.
5
Use a stethoscope or similar tool to pinpoint the source of the knocking sound.
6
Scan for any error codes using an OBD-II scanner.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Jack and jack stands
•Stethoscope (optional)

Parts Required

•Engine mounts (if applicable)
•CV joints or driveshaft (if necessary)
•Suspension components (if damaged)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the undercarriage for any loose or damaged components.
2
Verify engine mounts for wear or damage.
3
Check the condition of the driveshaft and CV joints for any signs of wear or damage.
4
Examine the suspension components, including control arms and bushings.
5
Use a stethoscope or similar tool to pinpoint the source of the knocking sound.
6
Scan for any error codes using an OBD-II scanner.

Solution

1. Preparation

Gather tools and parts needed for the repair.
Park the vehicle on a flat surface and engage the parking brake.
Disconnect the battery to ensure safety while working on electrical components.

2. Inspect and Replace Engine Mounts (if necessary)

Sub-steps:
- Locate the engine mounts; typically found at the front and rear of the engine.
- Use a socket set to remove bolts securing the mounts to the engine and chassis.
- Carefully lift the engine slightly using a jack and a piece of wood to avoid damage.
- Remove the old mount and compare it with the new one for compatibility.
- Install the new mount, ensuring all bolts are torqued to manufacturer specifications (refer to service manual for torque values).

3. Examine and Replace Driveshaft or CV Joints (if necessary)

Sub-steps:
- Raise the vehicle securely on jack stands and remove the front wheels.
- Inspect the driveshafts for any visible damage such as tears in the CV boot or play in the joint.
- If damaged, remove the retaining clips and bolts to disconnect the driveshaft from the wheel hub and transmission.
- Install the new driveshaft/CV joint, ensuring proper alignment and securing all bolts to the recommended torque specifications.

4. Check Suspension Components

Sub-steps:
- Visually inspect all suspension components including control arms, bushings, and struts for damage or excessive wear.
- Replace any damaged components, using a socket set to remove and install new parts.
- Ensure that all bushings are properly seated and that bolts are torqued to specification.