how to fix P0128 code in Renault Clio V (2019-Present)

Renault Clio V (2019-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

Error Code: P0128

4 min read

637 words

Problem Statement

Learn how to diagnose and fix P0128 cooling system issue in Renault Clio V. Step-by-step guide with diagnostic procedures and repair instructions.

Error Code

P0128

Affected Component

Cooling System

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the negative terminal of the battery to avoid electrical shorts.
•Allow the engine to cool down before starting work on the cooling system.

Symptoms

•Check engine light illuminated
•Engine temperature gauge reading lower than normal
•Poor fuel economy
•Engine running rich (excess fuel consumption)
•Heater not producing adequate heat
•Increased emissions

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to confirm P0128 is present.
2
Inspect the engine coolant level and condition.
3
Check the operation of the thermostat by monitoring the coolant temperature.
4
Test the coolant temperature sensor with a multimeter to ensure proper resistance readings.
5
Inspect wiring and connectors related to the coolant temperature sensor for damage or corrosion.
6
Verify that the engine coolant is not contaminated or mixed with oil.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Socket set
•Torque wrench
•Coolant funnel

Parts Required

•Thermostat
•Coolant temperature sensor
•Engine coolant

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to confirm P0128 is present.
2
Inspect the engine coolant level and condition.
3
Check the operation of the thermostat by monitoring the coolant temperature.
4
Test the coolant temperature sensor with a multimeter to ensure proper resistance readings.
5
Inspect wiring and connectors related to the coolant temperature sensor for damage or corrosion.
6
Verify that the engine coolant is not contaminated or mixed with oil.

Solution

1. Preparation

Gather tools and parts required for the repair.
Disconnect the negative terminal of the battery to avoid electrical shorts.
Allow the engine to cool down before starting work on the cooling system.

2. Inspect and Replace Thermostat

Tools Required: Socket set, torque wrench, gasket scraper, coolant catch pan.
Sub-steps:
1. Drain the engine coolant into a catch pan.
2. Remove the thermostat housing by unscrewing the bolts (note torque specifications for reinstallation).
3. Carefully take out the thermostat and inspect it for proper operation (it should open and close easily).
4. If faulty, replace it with a new thermostat that matches OEM specifications.
5. Clean the mating surfaces of the thermostat housing and engine block with a gasket scraper.
6. Reinstall the thermostat and housing, tightening the bolts to the specified torque.

3. Inspect and Replace Coolant Temperature Sensor

Tools Required: OBD-II scanner, multimeter, socket set.
Sub-steps:
1. Locate the coolant temperature sensor on the engine (refer to service manual for exact location).
2. Disconnect the electrical connector from the sensor.
3. Test the sensor's resistance using a multimeter; it should match the specifications given in the service manual.
4. If the readings are incorrect, remove the sensor using a socket, and replace it with a new one.
5. Reconnect the electrical connector securely.

4. Refill Engine Coolant

Tools Required: Coolant funnel.
Sub-steps:
1. Refill the engine with the appropriate coolant mixture (refer to the owner's manual for specifications).
2. Run the engine with the radiator cap off to allow air to escape, topping off the coolant as necessary.
3. Replace the radiator cap securely after all air has been purged.

5. Clear Error Codes

Tools Required: OBD-II scanner.
Sub-steps:
1. Reconnect the negative battery terminal.
2. Use the OBD-II scanner to clear the P0128 code from the vehicle’s computer.
3. Start the engine and monitor the temperature gauge for normal operation.