why is my Ram 1500 DT (2019-Present) making a clicking noise when driving?

Ram 1500 DT (2019-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

488 words

Problem Statement

Learn to diagnose and fix clicking noise in 2019 Ram 1500 DT. Step-by-step guide with diagnostic steps, tools required, and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components.
•Use jack stands to support the vehicle when working underneath it.

Symptoms

•Clicking noise during acceleration or deceleration
•Noise varies with vehicle speed, not engine RPM
•Possible vibration felt through the steering wheel
•Increased noise when turning or cornering
•Clicking may stop when coasting

Diagnostic Steps

1
Inspect the tires for any foreign objects or damage that could cause noise.
2
Check the wheel bearings for play or wear.
3
Examine the CV joints for signs of wear or damage, including torn boots.
4
Look for any loose components in the suspension system.
5
Test drive the vehicle to replicate the noise while monitoring for specific conditions (turning, accelerating).

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Flat-head screwdriver
•Floor jack and jack stands
•Bearing puller

Parts Required

•New tires (if needed)
•CV joint assembly (if needed)
•Wheel bearings (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the tires for any foreign objects or damage that could cause noise.
2
Check the wheel bearings for play or wear.
3
Examine the CV joints for signs of wear or damage, including torn boots.
4
Look for any loose components in the suspension system.
5
Test drive the vehicle to replicate the noise while monitoring for specific conditions (turning, accelerating).

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface and engage the parking brake.
Disconnect the battery to ensure safety during repairs.

2. Inspect and Replace Tires (if necessary)

Sub-steps:
1. Remove the wheel covers (if applicable) using a flat-head screwdriver.
2. Loosen and remove lug nuts with a socket wrench.
3. Inspect tires for punctures or embedded objects; replace if damaged.
4. Reinstall the wheel and securely tighten lug nuts to manufacturer specifications (typically 100-110 lb-ft).

3. Inspect and Replace CV Joints (if necessary)

Sub-steps:
1. Lift the vehicle using a floor jack and secure it on jack stands.
2. Remove the wheel and brake assembly to access the CV joint.
3. Inspect the CV boot for tears; if damaged, replace the CV joint assembly.
4. Install the new CV joint, ensuring it is properly seated and secured.
5. Reassemble the brake assembly and wheel, tightening everything to spec.

4. Inspect and Replace Wheel Bearings (if necessary)

Sub-steps:
1. Remove the wheel and brake assembly.
2. Use a bearing puller to remove the old wheel bearing.
3. Clean the hub area and install the new bearing, ensuring proper alignment.
4. Reinstall the brake assembly and wheel, tightening to manufacturer specifications.