why does my Ram 1500 DT (2019-Present) transmission slip when accelerating

Ram 1500 DT (2019-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

543 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix transmission slipping issues in Ram 1500 DT (2019-Present). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Allow the engine to cool before opening the transmission system to prevent burns.

Symptoms

•Check engine light illuminated
•Engine RPMs increase without a corresponding increase in vehicle speed
•Harsh or delayed shifting between gears
•Unusual noises coming from the transmission area
•Fluid leaks underneath the vehicle
•Poor fuel economy

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to check for any transmission-related trouble codes.
2
Inspect the transmission fluid level and condition; check for contamination or burnt smell.
3
Examine the transmission filter for clogs or restrictions.
4
Check for any visible leaks around the transmission and seals.
5
Test the operation of the transmission solenoids using a multimeter.
6
Perform a road test to replicate slipping behavior and observe any unusual sounds or performance issues.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Transmission fluid pump
•Funnel
•Drain pan
•Socket set
•Torque wrench
•Multimeter

Parts Required

•Transmission fluid (ATF+4)
•Transmission filter
•Transmission pan gasket
•Transmission solenoids (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to check for any transmission-related trouble codes.
2
Inspect the transmission fluid level and condition; check for contamination or burnt smell.
3
Examine the transmission filter for clogs or restrictions.
4
Check for any visible leaks around the transmission and seals.
5
Test the operation of the transmission solenoids using a multimeter.
6
Perform a road test to replicate slipping behavior and observe any unusual sounds or performance issues.

Solution

1. Preparation

Gather tools and parts required for the repair.
Park the vehicle on a flat surface and set the parking brake.
Disconnect the battery to ensure safety during repairs.

2. Check and Replace Transmission Fluid

Sub-steps:
1. Remove the transmission dipstick and check the fluid level.
2. If low, locate the fill port and add the recommended type of transmission fluid (typically ATF+4 for Ram trucks).
3. If the fluid is burnt or contaminated, drain the fluid from the transmission pan.
4. Replace the fluid with fresh transmission fluid.
Tools Required: Transmission fluid pump, funnel, drain pan, socket set.

3. Replace Transmission Filter

Sub-steps:
1. Remove the transmission pan using a socket set and drain any remaining fluid into a pan.
2. Carefully remove the old transmission filter.
3. Install a new filter, ensuring it is seated properly.
4. Reinstall the transmission pan with a new gasket and torque to manufacturer specifications (typically around 10-15 ft-lbs).
Tools Required: Socket set, torque wrench, gasket scraper.

4. Inspect and Test Solenoids

Sub-steps:
1. Remove the electrical connectors from the transmission solenoids.
2. Using a multimeter, test the resistance of each solenoid according to specifications.
3. If any solenoid is out of specification, replace it with a new one.
Tools Required: Multimeter.