my Ram 1500 DT (2019-Present) wipers are not working properly, what should I do?

Ram 1500 DT (2019-Present)

Error Codes

1-3 hours

Time

medium

Difficulty

medium

Severity

3 min read

532 words

Problem Statement

Learn how to diagnose and fix wiper issues on your Ram 1500 DT (2019-Present). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Electrical

Estimated Time

1-3 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components.
•Allow the engine to cool before starting any work in the engine compartment.

Symptoms

•Wipers do not operate at all
•Wipers operate intermittently
•Wipers operate at a slow speed
•Wipers get stuck in one position
•Wiper fluid does not spray

Diagnostic Steps

1
Check the wiper switch for proper operation.
2
Inspect the fuse related to the wiper system using the owner's manual for location.
3
Examine the wiper motor for any visible damage or corrosion.
4
Test the wiper motor with a multimeter to ensure it receives power.
5
Inspect the wiper linkage for any disconnections or damage.
6
Verify the condition of the wiper blades and arms.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Multimeter
•Wrench set
•Screwdriver set
•Wiper arm puller
•Fuse puller

Parts Required

•Wiper motor
•Wiper blades
•Fuses

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the wiper switch for proper operation.
2
Inspect the fuse related to the wiper system using the owner's manual for location.
3
Examine the wiper motor for any visible damage or corrosion.
4
Test the wiper motor with a multimeter to ensure it receives power.
5
Inspect the wiper linkage for any disconnections or damage.
6
Verify the condition of the wiper blades and arms.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface with the ignition off.
Disconnect the battery to prevent electrical shock.

2. Inspect and Replace the Fuse

Locate the fuse panel; refer to the owner's manual for specific location.
Remove the cover of the fuse box.
Use a fuse puller or pliers to extract the wiper fuse and inspect it for continuity.
If blown, replace it with a new fuse of the same amperage.

3. Test and Replace the Wiper Motor

Reconnect the battery and turn the ignition to the "On" position.
Use a multimeter to check the voltage at the wiper motor connector; you should see battery voltage.
If there is no voltage, further investigate wiring and switch.
If voltage is present but the motor does not operate, remove the motor by:
- Disconnecting the electrical connector.
- Unscrewing the mounting bolts (torque values as per service manual).
- Detaching the wiper linkage if necessary.
Install the new motor by reversing the removal steps.

4. Inspect and Repair the Wiper Linkage

If the wiper motor is functioning but wipers are not moving, inspect the wiper linkage.
Remove the wiper arms (using a wiper arm puller if necessary).
Check the linkage for breaks or disconnections; replace if damaged.
Reassemble the linkage and ensure it moves freely.

5. Replace Wiper Blades

Remove the old wiper blades by pressing the release tab and sliding off the blade.
Install new wiper blades by sliding them onto the wiper arm until they click into place.