how to solve Ram 1500 DT (2019-Present) remote start issues?

Ram 1500 DT (2019-Present)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

3 min read

547 words

Problem Statement

Learn how to diagnose and fix remote start issues in Ram 1500 DT (2019-Present). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Electrical

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems to prevent shorts or shocks.
•Ensure the vehicle is in a well-ventilated area during this process.

Symptoms

•Remote start button not responding
•Check engine light illuminated
•Vehicle does not start when remote start is engaged
•Door locks do not activate when remote start is attempted
•Security system indicator light flashing or illuminated
•Vehicle starts but shuts off immediately

Diagnostic Steps

1
Check the battery voltage of the key fob; replace if low.
2
Use an OBD-II scanner to check for any error codes related to the remote start system.
3
Verify that all doors, hood, and trunk are properly closed and secure.
4
Inspect the vehicle’s fuses related to the remote start and replace any blown fuses.
5
Test the remote start system with another key fob, if available, to rule out fob malfunction.
6
Ensure the vehicle is within range of the remote start signal (typically 300 feet).

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Small flathead screwdriver
•Fuse pullers or needle-nose pliers

Parts Required

•CR2032 key fob battery
•Replacement fuses (as needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the battery voltage of the key fob; replace if low.
2
Use an OBD-II scanner to check for any error codes related to the remote start system.
3
Verify that all doors, hood, and trunk are properly closed and secure.
4
Inspect the vehicle’s fuses related to the remote start and replace any blown fuses.
5
Test the remote start system with another key fob, if available, to rule out fob malfunction.
6
Ensure the vehicle is within range of the remote start signal (typically 300 feet).

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface and is in "Park" mode.
Disconnect the negative terminal of the battery to prevent any electrical shorts during repair.

2. Check and Replace Key Fob Battery

Sub-steps:
1. Open the key fob casing using a small flathead screwdriver.
2. Remove the old battery and replace it with a new CR2032 battery, ensuring correct polarity.
3. Reassemble the key fob casing securely.
Tools Required:
- Small flathead screwdriver

3. Inspect and Replace Fuses

Sub-steps:
1. Locate the fuse box (typically under the dashboard or engine compartment).
2. Identify the fuse related to the remote start system (refer to the owner’s manual for the exact location).
3. Remove the fuse using fuse pullers and visually inspect it for damage.
4. Replace any blown fuses with the same amperage rating.
Tools Required:
- Fuse pullers or needle-nose pliers

4. Perform System Reset

Sub-steps:
1. Reconnect the negative terminal of the battery.
2. Turn the ignition key to the "On" position without starting the engine, then turn it back to "Off."
3. Wait for 10 seconds, then attempt to use the remote start function again.
Safety Warnings:
- Ensure the vehicle is in a well-ventilated area during this process.