how to fix Honda Pilot YF3 (2016-2022) traction control light on

Honda Pilot Third Generation (2016-present)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

3 min read

550 words

Problem Statement

Learn how to diagnose and fix the traction control light issue in Honda Pilot YF3 (2016-2022). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Brakes

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow brake components to cool before inspection and cleaning.

Symptoms

•Traction control light illuminated on the dashboard
•Reduced engine power or hesitation during acceleration
•Unusual wheel slippage or loss of traction in slippery conditions
•Check engine light may also be present
•ABS warning light may be illuminated

Diagnostic Steps

1
Scan the vehicle's onboard diagnostics using an OBD-II scanner to retrieve error codes.
2
Inspect the wheel speed sensors for damage, dirt, or disconnection.
3
Check the integrity of the traction control fuse in the fuse box.
4
Verify the condition of the brake fluid and ensure it is within the recommended level.
5
Inspect the ABS module and wiring for signs of damage or corrosion.
6
Test the operation of the brake pedal position sensor.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Brake cleaner
•Socket set
•Torque wrench
•Fuse puller

Parts Required

•New traction control fuse (if blown)
•Brake fluid (DOT 3 or DOT 4)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan the vehicle's onboard diagnostics using an OBD-II scanner to retrieve error codes.
2
Inspect the wheel speed sensors for damage, dirt, or disconnection.
3
Check the integrity of the traction control fuse in the fuse box.
4
Verify the condition of the brake fluid and ensure it is within the recommended level.
5
Inspect the ABS module and wiring for signs of damage or corrosion.
6
Test the operation of the brake pedal position sensor.

Solution

1. Preparation

Gather necessary tools and parts.
Park the vehicle on a level surface and engage the parking brake.
Disconnect the battery to ensure safety during repairs.

2. Inspect and Clean Wheel Speed Sensors

Locate the wheel speed sensors at each wheel hub.
Remove the sensors by unscrewing the mounting bolts (if applicable).
Clean the sensors and the mounting area with brake cleaner to remove any dirt or debris.
Reinstall the sensors and torque the bolts to the manufacturer’s specification (usually around 7-10 Nm).

3. Check and Replace Traction Control Fuse

Locate the fuse box (usually under the dashboard or in the engine compartment).
Identify the traction control fuse by referring to the owner's manual or fuse diagram.
Pull the fuse out using a fuse puller and inspect it for continuity.
Replace with a new fuse of the same amperage if it is blown.

4. Inspect Brake Fluid Level

Open the hood and locate the brake fluid reservoir.
Check the fluid level; if low, top off with the recommended brake fluid (usually DOT 3 or DOT 4).
Inspect for any leaks in the brake system.

5. Reconnect Battery and Clear Codes

Reconnect the vehicle's battery and ensure all connections are tight.
Use the OBD-II scanner to clear any stored codes related to the traction control system.
Restart the vehicle and observe if the traction control light remains off.