why is my Honda CR-V Fifth Generation (2017-2022) engine making a knocking noise

Honda CR-V Sixth Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

476 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix engine knocking noise in Honda CR-V (2017-2022). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components.
•Allow the engine to cool before performing any inspections or repairs.

Symptoms

•Knocking noise from the engine, audible during acceleration and idling
•Reduced engine performance or power loss
•Engine misfires or rough idle
•Check engine light illuminated
•Unusual vibrations felt in the cabin

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any stored trouble codes.
2
Inspect the engine oil level and condition; check for signs of contamination or low oil.
3
Listen for the knocking noise with a mechanic's stethoscope to pinpoint the source.
4
Check the timing chain or belt for wear or misalignment.
5
Inspect engine mounts for wear or damage that could cause noise during operation.
6
Examine the fuel system for issues such as low fuel pressure or dirty fuel injectors.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Mechanic's stethoscope
•Torque wrench

Parts Required

•Engine oil (0W-20)
•Oil filter
•Timing chain (if necessary)
•Engine mounts (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any stored trouble codes.
2
Inspect the engine oil level and condition; check for signs of contamination or low oil.
3
Listen for the knocking noise with a mechanic's stethoscope to pinpoint the source.
4
Check the timing chain or belt for wear or misalignment.
5
Inspect engine mounts for wear or damage that could cause noise during operation.
6
Examine the fuel system for issues such as low fuel pressure or dirty fuel injectors.

Solution

1. Preparation

Gather tools: OBD-II scanner, socket set, mechanic's stethoscope, torque wrench.
Ensure the vehicle is on a level surface and the engine is cool.

2. Inspect and Replace Engine Oil

Sub-steps:
1. Remove the oil dipstick and check oil level.
2. If oil is low or dirty, drain the oil using a socket set to remove the oil drain plug.
3. Replace the oil filter with a new one.
4. Refill the engine with manufacturer-recommended oil (0W-20 for Honda CR-V).
5. Start the engine and let it idle, then check for the knocking noise.

3. Inspect Timing Chain/Belt

Sub-steps:
1. Remove the engine cover if necessary.
2. Check the timing chain tensioner for proper tension and wear.
3. If the timing chain is worn or stretched, replace it according to manufacturer specifications.
4. Reassemble the engine cover.

4. Examine Engine Mounts

Sub-steps:
1. Inspect engine mounts visually for cracks or separation.
2. If damaged, use a socket set to remove the old mounts and replace them with new ones.
3. Torque the new mounts to manufacturer specifications.