why does my Honda CR-V shake when I brake

Honda CR-V Sixth Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

554 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix brake shaking in Honda CR-V. Step-by-step guide with symptoms, diagnostic steps, tools, and repair instructions.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow brakes to cool before performing maintenance.

Symptoms

•Steering wheel shakes during braking
•Vibration felt in the brake pedal
•Unusual noise when brakes are applied
•Pulsation in the brake pedal
•Increased stopping distance

Diagnostic Steps

1
Inspect brake rotors for warping or uneven wear.
2
Check brake pads for wear and proper installation.
3
Examine the wheel assembly for loose or damaged components.
4
Inspect the suspension components for wear or damage.
5
Use a dial indicator to measure rotor runout.
6
Check tire balance and alignment.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Jack and jack stands
•Dial indicator

Parts Required

•Brake rotors
•Brake pads

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Solution

1. Preparation

Gather tools and parts needed for the repair.
Ensure the vehicle is parked on a level surface and the parking brake is engaged.
Disconnect the battery to avoid any electrical issues while working.

2. Remove Wheel

Use a socket set to loosen the lug nuts slightly while the vehicle is on the ground.
Lift the vehicle using a jack and secure it with jack stands.
Remove the lug nuts completely and take off the wheel.

3. Inspect and Replace Brake Components

A. Check Brake Rotors

Inspect the rotor surface for grooves or warping. If warped, proceed to replace the rotors.
To measure rotor runout, use a dial indicator. If runout exceeds manufacturer specifications, replace the rotor.

B. Replace Rotors (if necessary)

Remove the caliper by unscrewing the caliper bolts with a socket.
Slide the caliper off the rotor and support it with a bungee cord or wire to avoid stress on the brake line.
Remove the old rotor by unscrewing any retaining screws or using a hammer to tap it off gently if stuck.
Install the new rotor and secure it with retaining screws.

C. Check and Replace Brake Pads

Inspect the brake pads for thickness. If they are worn below 3mm, replace them.
Remove the caliper bracket bolts and slide off the bracket.
Remove the old brake pads from the bracket.
Install new pads, ensuring they are correctly positioned.

4. Reassemble Components

Reattach the caliper over the new pads and rotor.
Tighten the caliper bolts to the manufacturer’s torque specifications.
Reinstall the wheel and hand-tighten the lug nuts.
Lower the vehicle and torque the lug nuts to the specified value.

5. Final Checks

Reconnect the battery.
Pump the brake pedal several times to seat the new pads against the rotors before driving.