why does my Honda CR-V Fifth Generation (2017-2022) shake when I accelerate

Honda CR-V Sixth Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

512 words

Problem Statement

Learn how to diagnose and fix shaking during acceleration in Honda CR-V (2017-2022). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always use jack stands when the vehicle is raised.
•Disconnect the battery before working on electrical systems.
•Allow the vehicle to cool before working on the engine or transmission.

Symptoms

•Shaking or vibrating felt through the steering wheel or chassis during acceleration
•Increased noise from the engine or transmission
•Poor acceleration response or power loss
•Unusual tire wear patterns
•Steering wheel misalignment or pulling to one side

Diagnostic Steps

1
Inspect tires for proper inflation and visual damage.
2
Check for any loose or damaged suspension components.
3
Perform a wheel balance and alignment check.
4
Scan for diagnostic trouble codes (DTCs) using an OBD-II scanner.
5
Inspect drivetrain components (e.g., axles, CV joints, driveshaft) for wear or damage.
6
Test the engine and transmission mounts for signs of failure.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack and jack stands
•Torque wrench
•OBD-II scanner
•Socket set

Parts Required

•New tires (if necessary)
•Engine and transmission mounts (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect tires for proper inflation and visual damage.
2
Check for any loose or damaged suspension components.
3
Perform a wheel balance and alignment check.
4
Scan for diagnostic trouble codes (DTCs) using an OBD-II scanner.
5
Inspect drivetrain components (e.g., axles, CV joints, driveshaft) for wear or damage.
6
Test the engine and transmission mounts for signs of failure.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface and the engine is off.
Tools Required: Jack and jack stands, torque wrench, OBD-II scanner, socket set.

2. Tire Inspection

Sub-steps:
1. Inspect all tires for uneven wear and proper inflation.
2. Replace tires if they show significant wear or damage.
3. Rotate tires if necessary to promote even wear.
Safety Warning: Always use jack stands when the vehicle is raised.

3. Suspension and Drivetrain Examination

Sub-steps:
1. Visually inspect suspension components (control arms, bushings, struts) for wear or damage.
2. Check for loose bolts or connections and tighten or replace as needed.
3. Inspect axles and CV joints for any signs of cracking or leaking grease.
Tools Required: Socket set, torque wrench.

4. Wheel Balancing and Alignment

Sub-steps:
1. Take the vehicle to a professional service for wheel balancing.
2. Have a wheel alignment performed to ensure proper tracking.
3. If needed, adjust suspension components to manufacturer specifications.
Estimated Repair Time: 1-2 hours.

5. Engine and Transmission Mounts Replacement

Sub-steps:
1. Inspect engine and transmission mounts for cracks or excessive wear.
2. If necessary, remove the old mounts using a socket set and replace them with new ones.
3. Torque the new mounts to manufacturer specifications.
Tools Required: Socket set, torque wrench.
Parts Required: New engine and transmission mounts (if applicable).