why does my Honda CR-V Fifth Generation (2017-2022) make a popping noise when turning

Honda CR-V Sixth Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

525 words

Problem Statement

Learn how to diagnose and fix popping noise when turning in Honda CR-V 2017-2022. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always use jack stands when working under the vehicle.
•Ensure the vehicle is on a level surface before lifting.

Symptoms

•Popping or clicking noise when turning the steering wheel
•Noise occurs during both left and right turns
•Possible vibration felt through the steering wheel
•Uneven tire wear over time
•Difficulty in steering or a loose feeling in the steering wheel

Diagnostic Steps

1
Inspect the front suspension components visually for damage or wear.
2
Check the CV joints for any signs of grease leakage or deterioration.
3
Lift the vehicle and perform a physical inspection of the wheel bearings and tie rod ends.
4
Listen for noise while turning the steering wheel with the vehicle stationary.
5
Examine the power steering fluid level and condition.
6
Check for any loose bolts or nuts in the suspension and steering assemblies.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack
•Jack stands
•Socket set
•Torque wrench
•Pry bar
•Flashlight

Parts Required

•CV axle (if damaged)
•Suspension components (if worn)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the front suspension components visually for damage or wear.
2
Check the CV joints for any signs of grease leakage or deterioration.
3
Lift the vehicle and perform a physical inspection of the wheel bearings and tie rod ends.
4
Listen for noise while turning the steering wheel with the vehicle stationary.
5
Examine the power steering fluid level and condition.
6
Check for any loose bolts or nuts in the suspension and steering assemblies.

Solution

1. Preparation

Gather tools and safety equipment.
Required tools: jack, jack stands, socket set, torque wrench, pry bar, and a flashlight.
Safety warning: Always use jack stands when working under the vehicle and ensure the vehicle is on a level surface.

2. Lift the Vehicle

Use a jack to lift the front of the vehicle.
Secure the vehicle on jack stands to ensure safety while working underneath.

3. Inspect and Replace Damaged CV Joints

Inspection:
- Remove the wheel using a socket set.
- Inspect the CV joints for any cracks or torn boots.
Replacement:
- If damaged, remove the axle nut using a socket set.
- Disconnect the lower ball joint and remove the CV axle from the hub.
- Install the new CV axle, ensuring it is seated properly in the transmission.
- Reconnect the lower ball joint and torque to manufacturer specifications.

4. Check Suspension Components

Inspection:
- Check the control arms, bushings, and struts for any signs of wear or damage.
Replacement:
- If any components are worn, remove and replace with OEM parts.
- Use a torque wrench to ensure all bolts are tightened to the manufacturer's specifications.

5. Reassemble and Lower Vehicle

Reinstall the wheel and torque the wheel lug nuts to manufacturer specifications.
Carefully lower the vehicle from the jack stands.