why does my Honda CR-V Fifth Generation (2017-2022) make a clunking noise when turning

Honda CR-V Sixth Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

511 words

Problem Statement

Learn how to diagnose and fix clunking noise when turning in Honda CR-V 2017-2022. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always use jack stands when working under a vehicle.
•Allow the vehicle to cool before working on components.

Symptoms

•Clunking noise when turning the steering wheel
•Noise may vary with the speed of the vehicle
•Possible vibration felt through the steering wheel
•Increased noise during sharp turns
•Unusual tire wear patterns may be observed

Diagnostic Steps

1
Inspect the front suspension components for wear or damage, including control arms, bushings, and tie rods.
2
Check the CV joints for any signs of damage or excessive play.
3
Lift the vehicle and shake the wheels to determine if there is any play in the wheel bearings.
4
Examine the steering linkage for any loose or damaged parts.
5
Scan the vehicle for any error codes that may indicate related drivetrain issues.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Pry bar
•CV joint puller
•Ball joint separator

Parts Required

•CV joint (if damaged)
•Control arms and bushings (if worn)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the front suspension components for wear or damage, including control arms, bushings, and tie rods.
2
Check the CV joints for any signs of damage or excessive play.
3
Lift the vehicle and shake the wheels to determine if there is any play in the wheel bearings.
4
Examine the steering linkage for any loose or damaged parts.
5
Scan the vehicle for any error codes that may indicate related drivetrain issues.

Solution

1. Preparation

Gather necessary tools and parts.
Park the vehicle on a flat surface and engage the parking brake.
Disconnect the battery to prevent any electrical issues.

2. Inspect and Replace CV Joints

Tools Required: Socket set, torque wrench, pry bar, CV joint puller.
Sub-steps:
1. Lift the front of the vehicle using a jack and secure it on jack stands.
2. Remove the front wheels to access the CV joints.
3. Inspect the CV boots for tears or leaks. If damaged, replace the CV joint.
4. Use a CV joint puller to detach the joint from the axle.
5. Install the new CV joint, ensuring it is properly seated. Torque to manufacturer specifications.

3. Inspect and Replace Suspension Components

Tools Required: Socket set, torque wrench, ball joint separator.
Sub-steps:
1. Check the condition of the control arms and bushings. Replace any worn components.
2. Use a ball joint separator to detach control arms if necessary.
3. Install new control arms and bushings, ensuring all bolts are torqued to the specified values.
4. Reinstall the wheels and lower the vehicle.

4. Test Drive

Sub-steps:
1. Reconnect the battery.
2. Start the vehicle and take it for a test drive to ensure the clunking noise has been resolved.
3. Pay attention to any other noises or handling issues.