why does my Honda CR-V Fifth Generation (2017-2022) make a clicking noise when turning

Honda CR-V Sixth Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

551 words

Problem Statement

Learn to diagnose and fix the clicking noise when turning in Honda CR-V (2017-2022). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery before working on electrical systems.
•Ensure the vehicle is securely supported on jack stands before performing repairs.

Symptoms

•Clicking noise during left or right turns
•Noise occurs at low speeds
•Increased noise when turning sharply
•No noticeable change in steering feel
•Vibration in the steering wheel (in some cases)

Diagnostic Steps

1
Inspect the CV (Constant Velocity) joints for wear or damage.
2
Check the condition of the wheel bearings for play or noise.
3
Examine the suspension components, including struts and control arms.
4
Test drive the vehicle to replicate the clicking noise while turning.
5
Inspect the tires for uneven wear or any debris lodged in the tread.
6
Listen for any additional noises during acceleration or deceleration while turning.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Pry bar
•Jack and jack stands
•Wheel chocks

Parts Required

•CV joint assembly (if damaged)
•Wheel bearings (if worn)
•Suspension components (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the CV (Constant Velocity) joints for wear or damage.
2
Check the condition of the wheel bearings for play or noise.
3
Examine the suspension components, including struts and control arms.
4
Test drive the vehicle to replicate the clicking noise while turning.
5
Inspect the tires for uneven wear or any debris lodged in the tread.
6
Listen for any additional noises during acceleration or deceleration while turning.

Solution

1. Preparation

Gather necessary tools and safety equipment.
Park the vehicle on a level surface and engage the parking brake.
Place wheel chocks behind the rear wheels for additional safety.

2. Inspect CV Joints

Tools Required: Socket set, pry bar
Sub-steps:
1. Lift the front of the vehicle using a jack and secure it on jack stands.
2. Remove the front wheels for better access to the CV joints.
3. Visually inspect the CV joint boots for tears or leaks.
4. Check the CV joints for any signs of excessive play or clicking while rotating by hand.

3. Examine Wheel Bearings

Tools Required: Torque wrench, socket set
Sub-steps:
1. With the wheels removed, grasp the hub and check for play by moving it up and down.
2. If there is play, the wheel bearings may need adjustment or replacement.
3. Remove the wheel bearing assembly if necessary, following the manufacturer's specifications for torque settings during reassembly.

4. Inspect Suspension Components

Tools Required: Socket set, pry bar
Sub-steps:
1. Visually inspect all suspension components, including control arms and struts, for signs of wear or damage.
2. Use a pry bar to check for play in the bushings and ball joints.
3. Replace any worn or damaged components as needed.

5. Reassemble and Test

Reinstall the wheels and lower the vehicle to the ground.
Torque the lug nuts to the manufacturer's specifications.
Test drive the vehicle to confirm that the clicking noise has been resolved.