how to fix the P0720 speed sensor issue on Honda CR-V Sixth Generation (2023-present)?

Honda CR-V Sixth Generation (2023-present)

Error Codes

1-2 hours

Time

medium

Difficulty

high

Severity

Error Code: P0720

3 min read

499 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix P0720 speed sensor issues in Honda CR-V Sixth Generation. Step-by-step guide with diagnostic procedures and repair instructions.

Error Code

P0720

Affected Component

Transmission

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Allow the engine to cool before working on the transmission area.

Symptoms

•Check engine light illuminated
•Erratic speedometer readings
•Transmission slipping or hard shifting
•Poor acceleration response
•Increased fuel consumption

Diagnostic Steps

1
Scan the vehicle's onboard diagnostics using an OBD-II scanner to confirm the P0720 code and check for any related codes.
2
Inspect the vehicle speed sensor wiring and connectors for any signs of damage or corrosion.
3
Measure the resistance of the speed sensor using a multimeter to ensure it is within manufacturer specifications.
4
Check the vehicle’s transmission fluid level and condition, as low or dirty fluid can affect sensor performance.
5
Test the speed sensor output signal using a scope or multimeter while the vehicle is in motion.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Multimeter
•Torque wrench

Parts Required

•New vehicle speed sensor

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan the vehicle's onboard diagnostics using an OBD-II scanner to confirm the P0720 code and check for any related codes.
2
Inspect the vehicle speed sensor wiring and connectors for any signs of damage or corrosion.
3
Measure the resistance of the speed sensor using a multimeter to ensure it is within manufacturer specifications.
4
Check the vehicle’s transmission fluid level and condition, as low or dirty fluid can affect sensor performance.
5
Test the speed sensor output signal using a scope or multimeter while the vehicle is in motion.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a flat surface and the engine is turned off.
Disconnect the battery to prevent electrical short circuits.

2. Remove the Speed Sensor

Locate the vehicle speed sensor, typically found on the transmission housing.
Disconnect the electrical connector from the speed sensor.
Remove the mounting bolt(s) using a socket set.
Carefully pull out the speed sensor from its housing.

3. Inspect and Clean

Visually inspect the speed sensor for any physical damage or debris.
Clean the sensor mounting area to ensure proper sealing for the new sensor.

4. Install New Speed Sensor

Apply a small amount of engine oil to the O-ring of the new speed sensor to facilitate installation.
Insert the new speed sensor into its housing and secure it with the mounting bolt(s) to the specified torque (typically around 8-12 ft-lbs, refer to service manual for exact specification).
Reconnect the electrical connector firmly.

5. Reconnect Battery and Test

Reconnect the vehicle's battery.
Clear the error codes using the OBD-II scanner.
Start the engine and allow it to idle for a few minutes, then check for any new codes.