how to fix P0135 oxygen sensor code in Honda CR-V Sixth Generation (2023-present)

Honda CR-V Sixth Generation (2023-present)

Error Codes

1-2 hours

Time

medium

Difficulty

high

Severity

Error Code: P0135

3 min read

483 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix P0135 oxygen sensor code in Honda CR-V Sixth Generation (2023-present). Step-by-step guide with diagnostic procedures and repair instructions.

Error Code

P0135

Affected Component

Exhaust System

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before working on exhaust components.

Symptoms

•Check engine light illuminated
•Rough idle or engine stalling
•Decreased fuel efficiency
•Increased exhaust emissions
•Slow acceleration or loss of power

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to confirm the P0135 code.
2
Inspect the wiring and connectors leading to the upstream oxygen sensor for any damage or corrosion.
3
Check the oxygen sensor heater circuit resistance using a multimeter.
4
Verify the vehicle's engine coolant temperature is within normal operating range.
5
Check for any exhaust leaks upstream of the oxygen sensor.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Oxygen sensor socket
•Multimeter
•Torque wrench
•Electrical contact cleaner

Parts Required

•New upstream oxygen sensor

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to confirm the P0135 code.
2
Inspect the wiring and connectors leading to the upstream oxygen sensor for any damage or corrosion.
3
Check the oxygen sensor heater circuit resistance using a multimeter.
4
Verify the vehicle's engine coolant temperature is within normal operating range.
5
Check for any exhaust leaks upstream of the oxygen sensor.

Solution

1. Preparation

Gather necessary tools and parts.
Disconnect the negative battery terminal to prevent electrical shorts.
Allow the engine to cool completely before beginning work.

2. Remove the Oxygen Sensor

Locate the upstream oxygen sensor (usually positioned in the exhaust manifold or header).
Use an oxygen sensor socket or a wrench to carefully unscrew and remove the sensor.
Take care not to damage the threads in the exhaust manifold.

3. Inspect and Clean

Inspect the threads and connector of the removed oxygen sensor for damage or carbon buildup.
Clean the sensor's connector with electrical contact cleaner if corrosion is present.
Check the wiring insulation for any signs of wear or damage.

4. Install New Oxygen Sensor

Apply anti-seize compound to the threads of the new oxygen sensor if required (avoid getting any on the sensor tip).
Install the new oxygen sensor by screwing it in carefully to avoid cross-threading.
Tighten to the manufacturer's specified torque (usually around 30-40 ft-lbs).

5. Reconnect and Test

Reconnect the oxygen sensor's electrical connector securely.
Reconnect the negative battery terminal.
Start the engine and allow it to reach normal operating temperature.