why does my Honda CR-V Fifth Generation (2017-2022) transmission jerk when shifting

Honda CR-V 6th Gen (2023-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

538 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix transmission jerking in Honda CR-V (2017-2022). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components.
•Allow the engine and transmission to cool before working on them.

Symptoms

•Jerking or harsh shifting during acceleration
•Delayed engagement when shifting from park to drive or reverse
•Slipping sensation during gear changes
•Check engine light illuminated
•Unusual noises (e.g., grinding or whining) when shifting
•Decreased fuel efficiency

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any transmission-related trouble codes.
2
Check the transmission fluid level and condition (look for discoloration or burnt smell).
3
Inspect the transmission fluid filter for signs of blockage or contamination.
4
Examine the transmission control module (TCM) for software updates or fault codes.
5
Test the transmission solenoids for proper operation using a multimeter.
6
Visually inspect the transmission wiring harness for damage or loose connections.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Transmission fluid pump
•Funnel
•Socket set
•Screwdriver set
•Multimeter
•Torque wrench

Parts Required

•Honda ATF DW-1 transmission fluid
•Transmission filter (if applicable)
•Transmission control module (if replacement is necessary)
•Transmission solenoids (if replacement is necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any transmission-related trouble codes.
2
Check the transmission fluid level and condition (look for discoloration or burnt smell).
3
Inspect the transmission fluid filter for signs of blockage or contamination.
4
Examine the transmission control module (TCM) for software updates or fault codes.
5
Test the transmission solenoids for proper operation using a multimeter.
6
Visually inspect the transmission wiring harness for damage or loose connections.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface and the engine is off.
Disconnect the negative battery terminal to prevent electrical shorts.

2. Check and Replace Transmission Fluid

Sub-steps:
1. Remove the transmission dipstick and check fluid level.
2. If low, add the manufacturer-recommended transmission fluid (Honda ATF DW-1).
3. If fluid is dirty or burnt, drain the transmission fluid using a fluid pump and replace with fresh fluid.
4. Replace the transmission filter if applicable.
Tools Required:
- Transmission fluid pump
- Funnel

3. Inspect and Replace Transmission Control Module (TCM)

Sub-steps:
1. Locate the TCM (usually under the dashboard or near the transmission).
2. Disconnect the electrical connectors and remove the mounting screws.
3. Install the new TCM, ensuring all connectors are securely attached.
4. Reconnect the battery terminal.
Tools Required:
- Socket set
- Screwdriver set

4. Test Transmission Solenoids

Sub-steps:
1. Remove the transmission pan to access the solenoids.
2. Disconnect the solenoid connectors and remove the solenoids from their housing.
3. Test each solenoid with a multimeter for resistance as per the service manual specifications.
4. Replace any faulty solenoids and reassemble the transmission pan.
Tools Required:
- Multimeter
- Torque wrench (for re-installing the transmission pan)