my Honda CR-V Fifth Generation (2017-2022) is shaking when I brake what could it be

Honda CR-V 6th Gen (2023-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

517 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix brake shaking in Honda CR-V Fifth Generation (2017-2022). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Ensure the vehicle is securely supported on jack stands before working underneath.
•Allow the brakes to cool before inspection or replacement to prevent burns.

Symptoms

•Steering wheel vibrates during braking
•Pulsation felt in the brake pedal
•Uneven wear on brake pads
•Potential noise (squeaking or grinding) during braking
•Decreased braking efficiency

Diagnostic Steps

1
Inspect brake rotors for warping or damage.
2
Check brake pads for uneven wear and thickness.
3
Examine the brake calipers for proper operation and sticking.
4
Verify wheel alignment and tire condition.
5
Inspect suspension components (e.g., control arms, bushings) for wear.
6
Perform a brake fluid check for contamination or low levels.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Lug wrench
•Brake caliper tool
•Torque wrench
•Brake cleaner

Parts Required

•Brake pads
•Brake rotors

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect brake rotors for warping or damage.
2
Check brake pads for uneven wear and thickness.
3
Examine the brake calipers for proper operation and sticking.
4
Verify wheel alignment and tire condition.
5
Inspect suspension components (e.g., control arms, bushings) for wear.
6
Perform a brake fluid check for contamination or low levels.

Solution

1. Preparation

Gather tools and parts.
Park the vehicle on a level surface and engage the parking brake.
Use wheel chocks to prevent movement.

2. Remove Wheel

Tools Required: Socket set, lug wrench
Loosen the lug nuts slightly while the wheel is still on the ground.
Raise the vehicle using a jack and secure it with jack stands.
Remove the lug nuts completely and take off the wheel.

3. Inspect and Replace Brake Pads and Rotors

Tools Required: Brake caliper tool, torque wrench, brake cleaner
Remove the caliper bolts and carefully lift the caliper off the rotor; support it with a bungee cord or similar to avoid stress on the brake line.
Inspect the brake pads for uneven wear; replace them if they are worn down.
Measure rotor thickness and inspect for warping. If warped or below minimum thickness, replace the rotors.
Clean the rotor surface with brake cleaner before installation.

4. Reassemble Braking System

Reinstall new or resurfaced rotors onto the wheel hub.
Install new brake pads in the caliper bracket.
Reattach the caliper and torque the caliper bolts to the manufacturer's specifications (typically around 25-35 lb-ft, verify with repair manual).
Reinstall the wheel and hand-tighten the lug nuts.

5. Lower Vehicle and Finalize

Lower the vehicle from the jack stands.
Torque the lug nuts to the manufacturer's specifications (usually around 80-100 lb-ft).
Pump the brake pedal a few times to seat the brake pads against the rotors.