how to replace the brake pads on Honda CR-V Fifth Generation (2017-2022)

Honda CR-V 6th Gen (2023-Present)

Error Codes

1-2 hours

Time

medium

Difficulty

high

Severity

4 min read

608 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Step-by-step guide to replacing brake pads on Honda CR-V Fifth Generation (2017-2022). Learn symptoms, diagnostic steps, and necessary tools.

Affected Component

Brakes

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the negative battery terminal when working on brake systems.
•Ensure the vehicle is securely supported on jack stands before working underneath it.

Symptoms

•Squeaking or squealing noise when braking
•Vibration or pulsation in the brake pedal
•Reduced braking efficiency
•Warning light on the dashboard indicating brake system issue
•Increased stopping distance

Diagnostic Steps

1
Inspect brake pads visually for wear indicators.
2
Check brake fluid level in the master cylinder reservoir.
3
Test brake performance by pressing the pedal and observing response.
4
Listen for abnormal noises while applying brakes.
5
Check for any leaks in brake lines or around calipers.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Floor jack
•Jack stands
•Lug wrench
•Socket set
•C-clamp or brake caliper tool
•Torque wrench

Parts Required

•New brake pads
•Brake grease (for caliper and pad backing)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Solution

1. Preparation

Gather tools and parts required for the job.
Park the vehicle on a level surface and engage the parking brake.
Gather necessary safety equipment such as gloves and goggles.

2. Lift the Vehicle

Use a floor jack to lift the front or rear of the vehicle, depending on which brake pads are being replaced.
Secure the vehicle with jack stands for safety.

3. Remove the Wheel

Using a lug wrench, loosen the lug nuts while the vehicle is still on the ground.
Once lifted, fully remove the lug nuts and take off the wheel.

4. Remove the Brake Caliper

Locate the caliper mounting bolts (usually 2 bolts).
Use a socket set to remove the caliper bolts.
Carefully slide the caliper off the rotor. Do not let it hang by the brake line; support it with a bungee cord or similar tool.

5. Replace Brake Pads

Remove the old brake pads from the caliper bracket.
Compare new pads with old ones to ensure correct fit.
Install the new brake pads into the caliper bracket, ensuring they are seated correctly.

6. Compress the Caliper Piston

Use a C-clamp or brake caliper tool to compress the caliper piston back into its housing to accommodate the new thicker brake pads.
Ensure the piston is fully retracted before reinstallation.

7. Reinstall the Brake Caliper

Position the caliper back over the new brake pads and rotor.
Reinsert and tighten the caliper mounting bolts to manufacturer specifications (typically around 20-30 ft-lbs, but verify with a service manual).

8. Reinstall the Wheel

Place the wheel back onto the hub.
Hand-tighten the lug nuts.
Lower the vehicle and then tighten the lug nuts in a crisscross pattern to the specified torque (usually around 80-100 ft-lbs).

9. Final Checks

Pump the brake pedal several times to ensure proper pressure and to set the brake pads against the rotor.
Check brake fluid level again and top off if necessary.