how to fix Honda CR-V Fifth Generation (2017-2022) transmission jerking when shifting

Honda CR-V 6th Gen (2023-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

564 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix transmission jerking in Honda CR-V Fifth Generation (2017-2022). Step-by-step guide with tools and procedures.

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before opening the transmission pan to prevent burns.

Symptoms

•Jerking or harsh shifting during acceleration
•Delay in engagement when shifting from park to drive or reverse
•Unusual noises during gear changes (clunking or grinding)
•Check engine light illuminated
•Poor acceleration performance
•Increased RPM before shifting occurs

Diagnostic Steps

1
Scan the vehicle's onboard computer using an OBD-II scanner to check for any error codes related to the transmission.
2
Inspect the transmission fluid level and condition; low or dirty fluid can affect shifting performance.
3
Check for any visible leaks around the transmission pan and cooler lines.
4
Test the transmission control module (TCM) for proper function and signals.
5
Examine the throttle position sensor (TPS) for accurate readings and response.
6
Conduct a road test to replicate the jerking issue while monitoring transmission behavior.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Transmission fluid dipstick
•Funnel
•Rags
•Drain pan

Parts Required

•Transmission fluid (Honda ATF DW-1)
•Transmission filter (if applicable)
•Throttle position sensor (if defective)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan the vehicle's onboard computer using an OBD-II scanner to check for any error codes related to the transmission.
2
Inspect the transmission fluid level and condition; low or dirty fluid can affect shifting performance.
3
Check for any visible leaks around the transmission pan and cooler lines.
4
Test the transmission control module (TCM) for proper function and signals.
5
Examine the throttle position sensor (TPS) for accurate readings and response.
6
Conduct a road test to replicate the jerking issue while monitoring transmission behavior.

Solution

1. Preparation

Tools Needed: OBD-II scanner, socket set, transmission fluid dipstick, funnel, rags.
Park the vehicle on a level surface and engage the parking brake.
Disconnect the battery to ensure safety while working on electrical components.

2. Check and Replace Transmission Fluid

Remove the transmission dipstick and check the fluid level. If low, proceed to the next steps.
Place a drain pan under the transmission pan.
Remove the transmission pan bolts using a socket set and carefully drop the pan to drain the old fluid.
Inspect the transmission pan for metal shavings or debris; clean the pan thoroughly.
Replace the transmission filter if applicable, securing it in place.
Reinstall the pan with a new gasket and torque the bolts to the manufacturer’s specifications (typically around 12-15 ft-lbs).
Refill the transmission with fresh Honda ATF DW-1 fluid using a funnel until the appropriate level is reached.

3. Inspect and Replace Throttle Position Sensor (if needed)

Locate the throttle position sensor on the throttle body.
Disconnect the electrical connector from the TPS.
Remove the mounting screws and carefully pull the sensor off.
Install the new throttle position sensor and secure it with screws.
Reconnect the electrical connector.

4. Check Transmission Control Module (if needed)

Reconnect the battery and use the OBD-II scanner to recheck for any error codes.
If TCM issues are present, consider reprogramming or replacing the module.