how to fix Honda CR-V Fifth Generation (2017-2022) remote key not working

Honda CR-V 6th Gen (2023-Present)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

3 min read

532 words

Problem Statement

Learn how to diagnose and fix the remote key not working issue in Honda CR-V Fifth Generation (2017-2022). Step-by-step guide with tools and tips.

Affected Component

Electrical

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on any electrical components to prevent shorts or shocks.

Symptoms

•Remote key buttons do not respond when pressed
•Dashboard warning light for the keyless entry system illuminated
•Vehicle does not respond when attempting to start with the remote key
•Physical key inside the remote works to unlock the doors
•Battery in the remote has previously been replaced

Diagnostic Steps

1
Check the battery voltage of the remote key using a multimeter.
2
Inspect the remote key fob for physical damage or wear.
3
Verify that the vehicle's keyless entry system is functioning by testing the other remote (if available).
4
Check the vehicle's fuse related to the keyless entry system.
5
Scan the vehicle's onboard diagnostics with an OBD-II scanner for any related error codes.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Screwdriver set
•Multimeter
•OBD-II scanner
•Flat-head screwdriver

Parts Required

•CR2032 battery
•Replacement fuse

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Symptoms

•Remote key buttons do not respond when pressed

•Dashboard warning light for the keyless entry system illuminated

•Vehicle does not respond when attempting to start with the remote key

•Physical key inside the remote works to unlock the doors

•Battery in the remote has previously been replaced

Diagnostic Steps

1
Check the battery voltage of the remote key using a multimeter.
2
Inspect the remote key fob for physical damage or wear.
3
Verify that the vehicle's keyless entry system is functioning by testing the other remote (if available).
4
Check the vehicle's fuse related to the keyless entry system.
5
Scan the vehicle's onboard diagnostics with an OBD-II scanner for any related error codes.

Solution

1. Preparation

Gather tools: screwdriver set, multimeter, OBD-II scanner.
Ensure your workspace is clean and organized.
Disconnect the vehicle battery to avoid electrical issues.

2. Inspect and Replace Battery

Open the remote key fob with a small flat-head screwdriver.
- Tools Required: Flat-head screwdriver
Remove the old battery from the key fob.
Insert a new battery (CR2032 or as specified in the owner's manual).
Ensure the battery is installed with the correct polarity (+/-).
Close the key fob securely.

3. Check Fuses

Locate the fuse box (usually under the dashboard or in the engine compartment).
Identify the fuse for the keyless entry system (refer to the fuse diagram in the owner’s manual).
Inspect the fuse to see if it is blown.
- Sub-step: If blown, replace it with a new fuse of the same amperage.
Reconnect the vehicle battery.

4. Reprogram Remote Key

Sit in the driver's seat and close all doors.
Insert the key into the ignition and turn to the ON position without starting the engine.
Press the lock button on the remote for 1 second, then turn the ignition to OFF.
Repeat this process twice more (a total of three times).
After the third time, turn the ignition to the OFF position and press the lock button again.
Test the remote to see if it functions correctly.