Honda CR-V Fifth Generation (2017-2022) AC not blowing cold air how to fix

Honda CR-V 6th Gen (2023-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

559 words

Problem Statement

Learn how to diagnose and fix the AC not blowing cold air in Honda CR-V 2017-2022. Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

HVAC

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components.
•Wear safety goggles to protect eyes from refrigerant and debris.

Symptoms

•AC system makes unusual noises when activated
•Warm air blowing from vents
•AC compressor not engaging
•Intermittent cold air followed by warm air
•AC warning light illuminated on dashboard

Diagnostic Steps

1
Check the refrigerant levels using a manifold gauge set to determine if the system is undercharged.
2
Inspect the AC compressor for signs of damage or wear, and verify if it engages when the AC is turned on.
3
Examine the AC fuse and relay in the fuse box for continuity and proper function.
4
Inspect the cabin air filter for dirt and blockages that could restrict airflow.
5
Scan the vehicle’s onboard computer for any error codes related to the AC system.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Manifold gauge set
•Multimeter
•Socket set
•Safety goggles

Parts Required

•R-134a refrigerant
•New AC compressor (if needed)
•Cabin air filter

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the refrigerant levels using a manifold gauge set to determine if the system is undercharged.
2
Inspect the AC compressor for signs of damage or wear, and verify if it engages when the AC is turned on.
3
Examine the AC fuse and relay in the fuse box for continuity and proper function.
4
Inspect the cabin air filter for dirt and blockages that could restrict airflow.
5
Scan the vehicle’s onboard computer for any error codes related to the AC system.

Solution

1. Preparation

Gather tools: Manifold gauge set, multimeter, socket set, and safety goggles.
Ensure the vehicle is parked on a level surface with the engine off before starting work.

2. Check Refrigerant Levels

Connect the low and high-pressure sides of the manifold gauge set to the AC service ports.
Start the engine and turn on the AC to the maximum setting.
Read the pressure gauges; if low, proceed to recharge the system using R-134a refrigerant.

3. Inspect and Replace AC Compressor

Disconnect the vehicle battery.
Remove the drive belt by loosening the tensioner pulley.
Unbolt the AC compressor from its mounting bracket and disconnect the electrical connector.
Replace with a new compressor, ensuring it is properly aligned and securely fastened.
Reconnect the electrical connector and drive belt.

4. Replace Cabin Air Filter

Locate the cabin air filter compartment, usually found behind the glove box.
Open the glove box and remove it to access the filter.
Pull out the old filter and insert the new one, ensuring it is oriented correctly.
Reassemble the glove box.

5. Recharge AC System

After repairs, connect the manifold gauge set to the AC service ports once more.
Evacuate the system using a vacuum pump for about 30 minutes to remove moisture.
Recharge the system with the recommended amount of R-134a refrigerant.