why is my Honda CR-V Fifth Generation (2017-2022) making a clicking noise when turning

Honda CR-V Fifth Generation (2017-2022)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

508 words

Problem Statement

Learn how to diagnose and fix the clicking noise when turning in Honda CR-V (2017-2022). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the vehicle to cool before working on the brake components.

Symptoms

•Clicking noise when turning the steering wheel
•Noise increases with sharper turns
•Vibration felt through the steering wheel
•Possible loss of steering response
•Check engine light may be illuminated

Diagnostic Steps

1
Inspect the CV joints for wear or damage.
2
Check the condition of the wheel bearings for any play.
3
Examine the suspension components (control arms, bushings) for wear.
4
Lift the vehicle and rotate the wheels to listen for noise while stationary.
5
Scan for error codes using an OBD-II scanner to rule out electronic issues.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Pry bar
•Jack and jack stands
•OBD-II scanner

Parts Required

•CV joint assembly (if damaged)
•Wheel bearing (if needed)
•Suspension components (if worn)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the CV joints for wear or damage.
2
Check the condition of the wheel bearings for any play.
3
Examine the suspension components (control arms, bushings) for wear.
4
Lift the vehicle and rotate the wheels to listen for noise while stationary.
5
Scan for error codes using an OBD-II scanner to rule out electronic issues.

Solution

1. Preparation

Ensure the vehicle is parked on a level surface and the engine is off.
Gather necessary tools and parts.
Disconnect the battery to ensure safety while working on the vehicle.

2. Inspect and Replace CV Joints

Sub-steps:
1. Remove the wheel: Loosen lug nuts and lift the vehicle using a jack, then secure it with jack stands.
2. Remove the axle nut: Use a socket and torque wrench to remove the axle nut securing the CV joint.
3. Detach the CV joint from the hub: Use a pry bar if necessary to pop the CV joint out of the hub assembly.
4. Inspect the CV joint boots for tears; if damaged, replace the CV joint.
5. Install the new CV joint: Reverse the removal process, ensuring to torque the axle nut to the manufacturer's specifications (typically around 134 ft-lbs).

3. Check Wheel Bearings

Sub-steps:
1. Spin the wheel: After removing the wheel, spin it by hand and listen for grinding noises.
2. Inspect bearing play: Grip the wheel at 12 and 6 o'clock positions and check for excessive play.
3. If bearings are worn, replace them: Remove the hub assembly and install new bearings using a bearing press.

4. Inspect Suspension Components

Sub-steps:
1. Visually inspect control arms and bushings for wear or damage.
2. Use a pry bar to check for any play in the bushings.
3. If any components are damaged, replace them with OEM parts.

Tools Required:

Socket set
Torque wrench
Pry bar
Jack and jack stands
OBD-II scanner

Parts Required:

CV joint assembly (if damaged)
Wheel bearing (if needed)
Suspension components (if worn)

Estimated Repair Time: 2-4 hours

Safety Warnings:

Disconnect the battery before working on electrical systems.
Allow the vehicle to cool before working on the brake components.